Manuals / Intel / Computer Equipment / Switch

Intel 410 manual Date__________________, Name of RAIDset, Type of RAIDset, Target, Disks Used

Models: 410

1 60

Download 60 pages 35.31 Kb

Page 43

Date__________________

Chapter 3. Installing and Using the RAID Array 410 Manager for Windows NT

Record the information in the following table:

Date__________________

Name of RAIDset

Type of RAIDset

Target

LUN

Disk(s) Used

EK–SMRAC–IG. C01

3–13

Image 43

Intel 410 manual Date__________________, Name of RAIDset, Type of RAIDset, Target, Disks Used

Contents

Order Number: EK–SMRAC-IG.C01 Installation GuideGetting Started RAID Array 410 for Windows NT – IntelThird Edition, June Contents Figures Appendix A Configuration Records – Blank FormsRevision Level Revision RecordDate Page Document Structure About This GuideChapter 2: Host Adapter Installation Audienceviii Appendix A: Configuration RecordAssociated Documents Conventions6.Creating an Initial Configuration Chapter Pre-installationSteps Installation “Checklist”Perform a System Backup ∙The associated system hardware manuals Page 1.1Site Preparation 1.3Removing the RAID Array 410 from the Pallet 1.2Unpacking the RAID Array 410 SWXRA-YxFigure 1–2Unpacking the RAID Array Figure 1–3Installation of Ramp on Shipping Pallet1.4Placing the RAID Array 410 Enclosure 1.6.2 Installing PC Program Card in Controller 1.6.1 PC Program Card Handling PrecautionsFigure 1–4PC Program Card Slot Location 1.7Connecting the Controller to ComputerPage EK–SMRAC–IG.C01 Page Page 2.1Install the Host Adapter Host Adapter Installation – Intel-basedSystem2.1.2 Installing the Host Adapter 2.1.1 Preparing to Install the Host AdapterFigure 2–1Connecting SCSI Cable 2.2Installing the SubsystemEK–SMRAC–IG.C01 2.4.1 Windows NT Not Installed on System 2.3Configuration Utilities2.4.2 Windows NT Previously Installed Congratulations Page 3.1RAID Manager for Windows NT 3.4Setting Controller Communications 3.3Installing the RAID Manager Software3.5Setting the Controller Configuration Click on OK after making the above selections 3.6.1 Displaying Physical/Logical View of System 3.6Creating an Initial ConfigurationNOTES 6.Choose Modify from the choices listed 3.6.2 Practice Example: Creating a Single Disk 3.6.3 Practice Example: Creating a Stripeset 3.6.4 Practice Example: Creating a Mirrorset 3.6.5 Practice Example: Adding a Spare Disk 3.6.6 Practice Example: Deleting Storagesets Congratulations3.7Saving the RAID Configuration Target Date__________________Name of RAIDset Type of RAIDsetPage 4.1.1 Verifying that hszdisk.sys Loaded 4.1Completing Configurations under Windows NT1.Select Program Manager 4.1.2 Completing a New RAID Array Configuration2.Select Administrative Tools 3.Select Disk AdministratorFigure 4–3Disk Administrator Screen Display Understanding the Disk Administrator DisplayBefore proceeding, you should verify the following 3.Optional: Make disk logical names permanent Figure 4–6Tools Pull-DownChoices EK–SMRAC–IG.C014.1.3Changes to RAID Array Configuration EK–SMRAC–IG.C01 Configuration Records – Blank Forms Disks Used Date__________________Name of RAIDset Type of RAIDset TargetTarget Appendix A. Configuration Records – Blank FormsDate__________________ Name of RAIDset Type of RAIDsetDisks Used Date__________________Name of RAIDset Type of RAIDset TargetB.1 What is the CLI? Accessing the Command Line Interpreter CLIB.2 Accessing the CLI 3.Set the communications parameters to Manual Rating Reader’s CommentsMost-LikedFeatures Least-LikedFeatures Manual Order Number