JVC BR-D95U specifications SUB Panel, Rear Panel

2 CONTROLS, CONNECTORS AND DISPLAYS

2-2 SUB PANEL

The sub panel can be accessed by opening the operation panel. To open the operation panel, refer to the figure

below. 34

2 CONTROLS, CONNECTORS AND DISPLAYS
2-3 REAR PANEL
9	8	7	6
			TIME CODE	AUDIO IN	AUDIO OUT
		VIDEO	IN	CH1	CH1
SERIAL V / A	COMPOSITE
		REF
INOUT	RS-232CLINE IN
1		75
		ON

SERVICE USE ONLY

38

R[TIME CODE] switches

[DF/NDF] drop frame/non-drop frame mode switch (NTSC only)

●To set the time code drop frame/non-drop frame.

*Effective only when the [INT/EXT] switch is set to ÒINTÓ and the [PRESET] switch is set to

ÒPRESETÓ. DF: To write the time code in the Drop Frame mode. The [DF] indicator lights on the counter display. NDF: To write the time code in the Non-drop Frame mode.

[INT/EXT] time code select switch

●To select internal or external time code generation.

INT:	To use the internal time code generator.
EXT: To use an external time code generator.

REC/FREE Run mode select switch

●To select one of two Run modes available with the internal time code generator.

*Effective only when the [PRESET/REGEN] switch is set to ÒPRESETÓ and the [INT/EXT] switch to ÒINTÓ.

REC:	Time code runs only during recording.
FREE: Time code runs in real time regardless of
	the VCRÕs operating mode. Select this
	position for editing.

PRESET/REGEN select switch

●To select the Internal Time Code Generator mode.

*Effective only when the [INT/EXT] switch is set to ÒINTÓ.

TIME CDOE

	DF	INT	FREE PRESET
	NDF	EXT	REC	REGEN
RF	HID GND	OFF	8	ON
				36
		ON	4	OFF
		CF	(625)	ON SCREEN

3735

●For the NTSC signal system, the [4/8] switch is disabled.

*To set the color frame servo with these switches, set menu switch No. 008 <CAP

YLOCK> to ÒSW SELÓ. (See page 105)

[ON SCREEN] select switch Use to switch the on-screen menu ON/OFF. The on-screen information is output from the [LINE-2 SUPER] connector.

*If menu switch No. 513 <EDIT ON SCREEN> is set to ÒONÓ, you cannot turn the on-screen

Udisplay off. (See page 24)

Service connectors [RF] ... RF test signal output connector [HID] ... Trigger signal output connector

I[G] ... Ground connector

[SERVICE USE ONLY] connector

Used to diagnose malfunctions and for other service procedures.

How to open the operation panel

●Lift the bottom edge of the panel to open it. The operation panel can be locked in 6 steps in the range of 0 to 90û.

							OFF
				2	REMOTE IN (9P) Y	Y	OUT	CH2	CH2
				AES / EBU	R-Y	R-Y	LINE1
			IN	OUT	REMOTE OUT (9P)
			CH1/2	CH1/2
					B-Y	B-Y	L	CH3	CH3
							LINE2
			CH3/4	CH3/4	VIDEO CONTROL		SUPER
					IN	OUT	OUT
					COMPONENT		COMPOSITE
							R	CH4	CH4
							AUDIO MONITOR
	1	2	3		4	6			5
1[AC IN] socket							[TIME CODE IN] connector ... XLR
	Connect to an AC power outlet via the provided						● Accepts external LTC time code signals
	power cable.						conforming to the SMPTE/EBU standard.
	● When usage voltage is 120 V or less; use the						Connect this connector to an external time code
	A-type (flat-pin type) power cable.						generator. A signal containing a large amount of
	● When usage voltage is 127 V or over; use the						jitter cannot be used for LTC time code. Be
2	C-type (round-pin type) power cable.						sure to use a regenerated signal (stable signal
							matched with the phase of video signals).
	[SIGNAL GND] ground terminal					7
							[REF IN] external sync signal input connector/
3This terminal is a GND for signals among unit.
							75 terminating switch (loop-through) .... BNC
	[AES/EBU IN] connector .... BNC x 2						● Accepts external reference sync signals.
	Accepts digital audio interface standard (AES/						Because of its loop-through design, this
	EBU) digital audio signals.						connector can distribute signals to other units
	These signals cannot be input if the optional						through the opposite terminal. Set the
	SA-D95U digital interface board is not installed.						terminating switch to OFF when distributing
							signals.	If signal distribution is not desired or is
	Always input external sync signals when inputting
							terminated at this unit, set the switch to ON.
	digital signals. Both video and audio must be
							● Does not accept signals with an input level over
	synchronized with the external sync signal.
							1 Vp-p.
	When the serial digital inputs and outputs of						* When setting up an editing system, input a
	several VCRs are connected in series, do not						black burst or standard color signal to
	input the same signal to each VCR as they					8	this unit. The [GEN] indicator will light.
	may not be input correctly. Digital audio						[COMPOSITE IN] connectors
	signals, in particular, will not be input correctly						[LINE IN] video line input connector ...BNC
4	to the next VCR in the series.						● Accepts composite video signals.
							Input composite signals passed through the
	[Y.R-Y.B-Y IN] component signal input					9	TBC.
	connector .... BNC x 3						[SERIAL V/A IN] connectors ... BNC

PRESET: Select this mode to preset time code data. REGEN: Select this mode when using the internal time code generator in sync with a

Tplayback time code signal.

[CF] color frame servo switches Use to switch the color frame servo ON/OFF.

●For the PAL signal system, select the 4 or 8 field color frame servo with the [4/8] switch on the side.

Lock release lever Lock release lever

●To return the panel to its original position, pull the lock release levers in the direction shown by the

arrows and push down the panel.

●Accepts component video signals.

Set menu switch No. 104 <CPN LEV./SETUP (525)> to select MII (LOW), Bcam (HIGH) and the presence of setup signals (NTSC only).

5The default setting is Bcam with setup.

[AUDIO IN] connector .... XLR x 4

●Accepts analog audio signals.

●Set the input level with menu switches No. 224 to 227 <AUDIO IN LEVEL>. The factory setting is +4 dB.

●Accepts serial video/audio signals. The lower connector is an active loop through connector. If the VCR is not turned on, no signal will be output. Serial signals cannot be input if the optional SA-D95U digital interface board is not installed. Always input external sync signals when inputting digital signals. Both video and audio must be synchronized with the external sync signal.

18 19