JVC BR-D95U specifications Color Frame Servo Setting, Editing procedure, Preparation

11 EDITING

11-2 COLOR FRAME SERVO SETTING

Color frame reference

VIDEO IN				LINE IN monochrome input
		LINE IN color signal input		COMPONENT IN
REF IN				SDI IN
	REC	EDIT PB	PB	REC	PB
REF IN is	LINE IN	LINE IN	REF IN	REF IN	REF IN
Gen locking
REF IN is not			Internal	Color frame	Internal reference
Gen locking			reference	information is	signal
			signal	recorded according
				to the time code.
The color frame sync condition of the playback shown in the table above changes depending on the setting of menu switch No. 008 <CAP
LOCK>.

TC color frame flag setting

●The time code color frame flag can be set and recorded only when the front sub panel’s [TIME CODE] switches are set as follows.

[INT/EXT] switch		: INT
[PRESET/REGEN] switch : PRESET
When the [TIME CODE] switches are set as above, the time code color frame flag is recorded according to
the setting of menu switch No. 421 <TCG CF FLAG MODE>.
Menu switch	During playback	During EE output
NO. 421 <TCG
CF FLAG	TCG CF FLAG setting		CF FLAG being recorded on tape
MODE>
OFF	OFF information	OFF information	OFF information is recorded
	is output	is output
ON	ON information	ON information	ON information	● When recording time code with the [INT/EXT] switch set to “INT”
	is output	is output	is recorded	and the [PRESET/REGEN] switch set to “PRESET” (except in
				editing)
				* Time code is based on the information recorded before the
				recording is paused. (i.e. “REC” [ “PAUSE” [ “REC” ) with the
				REGEN or REC RUN setting.

11 EDITING
11-3 SWAP EDITING
This unit is provided with a SWAP editing function which enables automatic editing without a controller. When this
unit is connected to a player provided with a RS-422 serial remote connector (9-pin), you can operate both units
using the recorder’s controls.
An on-screen function allows you to check editing data for faster, more efficient editing.
During swap editing, all the player can be operated from the recorder.
Editing procedure
STEP-1	STEP-2	STEP-3	STEP-4	STEP-5	STEP-6	STEP-7
Preparation	Edit mode	Edit point	Preview editing	Edit point	Editing	Review	Next
	selection	entry	(rehearsal)	correction	(actual)	(check)	edit
Preparation			Editing			Check

●When only edit start is performed automatically, steps 4, 5 and 7 can be omitted depending on the editing method (for example, preview editing is not required).

STEP-1 preparation

Connection

•Make sure all video and audio input/output connectors are properly connected.

•Connect the BR-D95U’s [REMOTE OUT(9P)] connector to the player’s RS-422 serial remote connector with the 9-pin remote cable.

Setting

Setting the player

•Set the VCR operation mode to the REMOTE mode.

•Adjust the video control parameters.

•Adjust the playback level with the audio playback level adjust knobs (this is not necessary for UNITY).

•Set the edit OUT point registering method with menu switch No. 373.

				● To record time code during assemble or time code insert editing
				(with tape recorded on BR-D95U).
				* Set menu switch No. 410 <AUTO REGEN MODE> to a valid
				setting (or set to “OFF” if the [PRESET/REGEN] switch is set to
				“REGEN”) and the [INT/EXT] switch is set to “INT” under the 4-
				field (8-field in PAL) color frame servo.
			OFF information	● When recording time code under any conditions except those
			is recorded	described above.
AUTO	The information	The same	ON information	● When recording time code with the [INT/EXT] switch set to “INT”
	recorded on the	setting as the	is recorded	and the [PRESET/REGEN] switch set to “PRESET” (except in
	tape is output.	one of TCG CF		editing)
		FLAG being		* Time code is based on the information recorded before the
		recorded on the		recording is paused. (i.e. “REC” [ “PAUSE” [ “REC” )with the
		tape is output.		REGEN or REC RUN setting.
				● To record time code during assemble or time code insert editing
				(with tape recorded on BR-D95U).
				* Set menu switch No. 410 <AUTO REGEN MODE> to a valid
				setting (or set to “OFF” if the [PRESET/REGEN] switch is set to
				“REGEN”) and the [INT/EXT] switch is set to “INT” under the 4-
				field (8-field in PAL) color frame servo.
			OFF information	● When recording time code under any conditions except those
			is recorded	described above.
* The set time code value may shift when menu switch No. 421 <TCG CF FLAG MODE> is set to “ON” or “AUTO” and recording is
performed with TC PRESET.

9P color frame flag

9P color frame flag is set when the setting of menu switch No. 387 <CF FLAG REPLY> matches that of menu

switch No. 008 <CAP. LOCK>.

Setting the recorder

●Front panel setting

•Set the VCR operation mode to “Local” with the [REMOTE] button (the [REMOTE] indicator on the display goes out).

•Select the input signal with the video and audio input signal select buttons.

•Adjust the recording level with the audio recording level adjust knobs (this is not necessary for UNITY).

•Set the counter mode with the [COUNTER] button.

●Front sub panel setting

Set the time code-related switches for time code editing.

(When editing the time code, be sure to input an external sync signal to the recorder and player.)

•[INT/EXT] switch: Set to “INT”.

•[REC/FREE] switch: Set to “FREE”.

•[PRESET/REGEN]: Set to “PRESET”.

●Menu switch setting

•No. 003 <SYNC SELECT>: Set to “EXT (1)” to synchronize with an external sync signal.

•No. 320 <PREROLL TIME>: Set the preroll time.

•No. 328 <EDIT POINT CLEAR>: Set whether or not the edit IN point is canceled when editing is complete.

•No. 367 <EDIT INTERRUPTION>: Set whether or not the editing operation is stopped when an error occurs in the video signal during preroll editing .

•No. 372 <P+R AT SWAP MODE>: Set whether or not pressing the [RECORDER] and [PLAYER] buttons simultaneously is possible.

•No. 373 <MATCH FRAME>:This setting determines whether or not the match frame function is used.

•No. 390 <SWAP VTR SELECT>: Set according to the type of player VCR. Normally set to “AUTO”.

•No. 391 <SYNCHRONIZATION>: Switch the Bump mode ON/OFF during swap editing.

•No. 393 <SYNC GRADE>: Select the editing accuracy during swap editing.

•No. 395 <AUTO EE>: Set whether or not the auto EE function is used during swap editing.

Set to “AUTO-EE (1)” when using only one monitor for editing.

•No. 513 <EDIT ON SCREEN>: Selects whether or not the edit display is shown on screen during editing.

106 107