JVC BR-D95U 0SEC, 15SEC, Still, Diag AT OFF Power on, JOG Feeling, Vid-Off, Vid-On/Aud-On

5 MENU SWITCH SETTING DETAILS

5 MENU SWITCH SETTING DETAILS

5-2 MENU SWITCH SETTING CONTENT
[	] : Factory setting
	Item		Setting
Menu SW	On-screen	Counter	On-screen		Content
No.	display	display	display
320	PREROLL TIME	0	0SEC	Sets the preroll time when the [PREROLL] button is
		...	...	pressed.
		[5]	[5SEC]	The preroll time can be selected from 0 second to
		...	...	15 seconds.
		15	15SEC
323	PREROLL END	0	STANDBY-ON	Selects which operation mode is engaged after
	MODE	[1]	[STILL]	preroll is executed.
				STANDBY-ON : Engages the Standby ON mode.
				STILL	: Engages the Still mode.

5-2 MENU SWITCH SETTING CONTENT
	[ ] : Factory setting
	Item		Setting
Menu SW	On-screen	Counter	On-screen
No.	display	display	display
357	DIAG AT	[0]	[OFF]
	POWER ON	1	ON

Content

Selects whether or not self-diagnosis is executed when the power is turned on.

OFF: Self-diagnosis is not executed. ON : Self-diagnosis is executed. However, if no tape is loaded when the power is turned on, self-diagnosis does not take place. While diagnostics are running (“DIAGNOSTIC” blinks on the screen), you cannot load a cassette. Do not try to forcibly load it. After completion of diagnostics, a warning indication is shown if there is an abnormality.

328	EDIT POINT	0	DISABLE
	CLEAR	[1]	[ENABLE]
340	SEARCH SPEED	[0]	[x 32]
		1	x 17
		3	x 6

Selects whether the edit point data is cleared after

performing the edit

DISABLE : The edit point is not cleared.

ENABLE : The edit point is cleared.

Selects the maximum search speed when using

the search dial.

X32 : Maximum search speed is +/-32 times

359	JOG FEELING	[0]	[TYPE-1]
	(REMOTE)	1	TYPE-2
		2	TYPE-3
		3	TYPE-4
		4	TYPE-5

Refer to “Warnings with Indicators” on page 145.

Alters the operation “feel” of the connected editing controller's jog dial.

Five settings (TYPE-1 (0) to TYPE-5 (4)) are available.

351	PREREAD	[0]	[VID-OFF/
			AUD-OFF]
		1	VID-ON/
			AUD-OFF
		2	VID-OFF/

	normal.
X17	: Maximum search speed is +/-17 times
	normal.
X6	: Maximum search speed is +/-6 times
	normal.
Selects whether or not the preread function is
activated. Video and audio preread functions
can be set independently.
VID-OFF/AUD-OFF : Both video and audio
	preread are disabled.

363	CONTROLLER	[0]
	SELECT	1
		2
		3
		4
		5
		6
		7

[DEFAULT] RM-450NOT DEFINED NOT DEFINED NOT DEFINED NOT DEFINED NOT DEFINED NOT DEFINED

This menu changes the characteristics of the VCR
to match specific types of controllers.
DEFAULT : Normally set to this position. This
	position is ready for standard editing
	controllers.
RM-450	: Set to this position for an editing remote
	controller which outputs JOG
	commands for synchronization.
(e.g.) SONY RM-450
NOT DEFINED - TYPE-7: Not defined.

	AUD-ON
3	VID-ON/
	AUD-ON

VID-ON/AUD-OFF	: Only video preread is
	enabled.
VID-OFF/AUD-ON	: Only audio preread is
	enabled.
VID-ON/AUD-ON	: Both video and audio
	preread are enabled.

367	EDIT INTER-	[0]	[OFF]	Selects whether or not editing aborts when the
	RUPTION	1	ON	audio condition degrades during PREROLL.
	(525)			OFF : Does not stop editing.
				ON : Stops editing. Error message is shown on the
				counter display.

352	AUD PREREAD	[0]	[NORMAL]
	TIMING	1	OFF SET

*When using the [REC] button to start recording, be sure to set this switch to “VID- OFF/AUD-OFF”.

Selects whether or not to apply correction during audio preread. Correction is based on output audio phase delay set with the audio control menu <AUDIO OUTPUT PHASE>. NORMAL : Does not apply correction. OFF SET : Applies correction to the output audio phase according to the delay of the connected video device.

368	STARTING PIC	[0]	[OFF]
	FREEZE	1	ON

*When this menu switch is set to “ON” and playback starts from a still image containing the block noise, still images containing block noise are output until the servo indicator lights.

To avoid this, obtain a clear still image before starting playback (using the jog dial or frame advance/reverse buttons).

Selects playback pictures or a still image as the video output until the servo locks.

OFF : A playback picture is displayed. The picture may be noisy until the servo stabilizes. ON : A still image is displayed. This changes to playback video when the servo stabilizes.

56 57