Basic Operations |
| |
|
| |
■ Remote control unit |
| |
Quick Alignment Function | ||
| ||
| (QUICK ALIGN.) | |
|
|
Basic Operations
■ Remote control unit | Displaying a Still Picture (FREEZE) |
|
While projecting an image, a still picture is obtained at any time by using the FREEZE button on the remote control.
QUICK ALIGN.
QUICK
ALIGN.OPERATE
The Quick Alignment function automatically adjusts (sets) the screen settings of the image input from the PC1, PC2 or DVI input terminals. This can only be performed from the remote control.
QUICK
ALIGN.
HIDE |
W |
OPERATE
When you press the FREEZE button:
“FREEZE” appears on the screen for a few seconds and
then the still picture is shown on the screen. Refer to the
button W
HIDE
SCREEN | FREEZE |
S |
|
COMP VIDEO
FREEZE button
FREEZE message shown on the left of this page.
SCREEN | FREEZE | COMP | VIDEO |
S |
|
|
|
PC1 | PC2 | DVI | Y/C |
| T | T |
|
KEYSTONE | DIGITAL | ZOOM | FOCUS |
ZOOM | |||
| W | W |
|
| PRESET |
| MENU |
| EXIT |
| ENTER |
While projecting an image on the screen, press the QUICK ALIGN. button on the remote control.
Quick alignment is conducted to obtain best image.
*During the automatic alignment, “Quick Alignment” appears on the screen, and then disappears when the alignment is completed.
Remote control unit
QUICK
DIGITAL ZOOM T/W button
PRESET button
EXIT button
PC1 | PC2 |
| T |
KEYSTONE | DIGITAL |
ZOOM | |
| W |
| PRESET |
| EXIT |
DVI Y/C
T
ZOOM FOCUS
W
MENU
ENTER
Cursor buttons 5/∞ / 2/3
When you press the FREEZE button again.
The original image resumes.
Remote control unit | FREEZE |
Notes
No.51931
ALIGN.
[Screen display]
Q u i c k A l i g n m e n t
Notes
•This only works for the signals input from the PC1, PC2 or DVI input terminals. It does not work for the signals input from the AV IN terminal (VIDEO, Y/C or COMP input terminal).
•The quick alignment function is used to automatically adjust
the “Horizontal and vertical position”, “Phase” and “Tracking” of the projected image.
•When using the quick alignment function to automatically adjust the image, use a bright,
FREEZE message
FREEZE
FREEZE inhibit message
FREEZE
DIGITAL ZOOM inhibit message
D.ZOOM
•During freezing, the picture sent from the signal source is lost.
•If any of the inoperative buttons (“MENU”, “QUICK ALIGN.”, “KEYSTONE”) are pressed while displaying a still picture, “FREEZE” is displayed on the screen.
•This function will not work with some signal sources
(UXGA, etc). In this case, the FREEZE inhibit message
appears for a few seconds, as shown on the left. To forcibly clear this message, press the EXIT button.
Zooming a Part of the Image
(DIGITAL ZOOM T/W)
A part of the image being projected can be digitally magnified up to four times. When the DIGITAL ZOOM T or W button is
pressed, “Digital zoom” appears on the screen together with the level bar and magnifying power ( ⋅ 1.0, ⋅ 1.2, ⋅ 1.4, ⋅ 1.6, ⋅ 2.0,
⋅2.5, ⋅ 3.2, ⋅ 4.0). When “15 sec.” is displayed in the menu, “Digital zoom” will appear in approximately 15 seconds.
Digital zoom | 1.2 |
•To zoom up or zoom down, press the DIGITAL ZOOM T or W button on the remote control.
Remote control unit
T
DIGITAL
ZOOM
W
Moving the zoomed image:
While “Digital zoom” appears on the screen, you can move
the zoomed image with the cursor ( 5/∞/2/3) button on the remote control.
5: Upper part of the image will be displayed.
∞: Lower part of the image will be displayed.
2: Left side part of the image will be displayed.
3: Right side part of the image will be displayed.
Notes
•This function will not work with some signal sources (UXGA, etc). In this case, the DIGITAL ZOOM inhibit
message appears for a few seconds, as shown on the left. To forcibly clear this message, press the EXIT button.
•The quality of the zoomed image reduces in comparison with the original one.
•To return to the original size ( ⋅ 1.0) and original position, press the PRESET button while “Digital zoom” is displayed
on the screen.
ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH
DLA- DLA-
36
1-19
37