JVC DLA-G150CLU, DLA-G150CLE 1-21, Menu Transition Diagram in PC Menu Mode, No.51931, Dla- Dla

Menu Operations

.
■ Quick Reference Guide			for Video Menu Mode
Main Menu in Video Menu Mode (While receiving video-device-related signals)
	Image adj. → (Refer to page 49)
		Contrast:	Contrast of the video image being projected can be adjusted. (–30 to +30, 0*)
		Brightness:	Brightness of the video image being projected can be adjusted. (–30 to +30, 0*)
		Color:	Color density of the video image being projected can be adjusted. (–30 to +30, 0*)
		Tint:	Tint of the video image being projected can be adjusted. (–30 to +30, 0*)
		Sharpness:	Sharpness of the video image being projected can be adjusted. (–5 to +5, 0*)
		All reset:	Resets above items to the factory set values.
			Yes / No
	Set up 1

Menu Operations

■Menu Transition Diagram in PC Menu Mode

Main menu in PC Menu ModeSubmenus in PC Menu Mode

Press 5/∞ to select an item.			Press 5/∞ to select an item.		Press 2/3 to select Yes or No.
					Then, press ENTER to execute.
			Press 2/3 to set or adjust the value.
Menu					Image adj.
Image adj.	Contrast	3 or
Set up			Image adj.	EXIT
	Brightness	ENTER			All reset?
Color temp.	Sharpness		Contrast	12
Options	All reset			ENTER	Yes	No
		EXIT	Brightness	12
Language			Sharpness	1 2 3 4 5
Information			All reset	ENTER

Position:			Video screen position and menu position can be adjusted.	→ (Refer to page 51)
		Disp. Posi. / Menu			→ (Refer to
Gamma:			Image tone can be changed. Down/Cinema*/Up (Suitable for the cinema programes)
			page 52)
Aspect ratio			Selectable aspect ratio, 4:3*/16:9. → (Refer to page 52)
Decoder:			Selectable color systems, Normally, set to AUTO.	(Refer to page 45)
			(This item is displayed only when inputting VIDEO or Y/C.)
		AUTO*/NTSC/NTSC4.43/PAL/SECAM
Page 2 Press ENTER to enter the “Set up 2” submenu
	Tracking: Normally, no adjustment is required. The lateral size and display area of video image can be
			adjusted. (–128 to + 127) → (Refer to page 47)

5
5			∞
	Menu
	Image adj.	Tracking
	Set up	Phase
	Color temp.
		Position
	Options
	Language	Resize
	Information	Clamp

					Press ENTER to select an item.
Press 5/∞ to select an item.					Press 5/∞ / 2/3 to move the
					video screen/menu position.
Press 2/3 to set or adjust the value.
					Position
3 or	Set up 1
	Tracking		123		ENTER
ENTER Phase
			12		Disp.Posi.	Menu
	Position		ENTER		12,12	ENTER
EXIT	Resize	1:1	Panel	Aspect	EXIT
	Clamp	ST		BP

No.51931

		Deinterlace:	Set when watching movies which were recorded on film.		→ (Refer to page 47)
		Phase:	Flickering or dim picture image can be adjusted. (0 to 31)
		Screen:	Selectable screen’s aspect ratio. 4:3*/16:9	→ (Refer to page 46)
		HDTV:	Selectable HDTV format. Normally, set to 1080i, 1080i*/1035i		→ (Refer to page 46)
		Page 1:	Press ENTER to return to “Page 1” submenu.
Color temp.
	Color temp.:		Adjustable color temperature, Low/Middle*/High.
			Will be adjusted to correct reddish or blueish image.
	RED:		Adjusts the red level. (0 to 255, the adjustable range varies depending on signals)
	GREEN:		Adjusts the green level. (0 to 255, the adjustable range varies depending on signals)
	BLUE:		Adjusts the blue level. (0 to 255, the adjustable range varies depending on signals)
	All-reset:		Reset above items to the factory set values.

5		∞
Menu
Image adj.
Set up	Color temp.
	RED
Color temp.
Options	GREEN
Language	BLUE
Information	All reset

Set up 1

Position		ENTER
Resize	1:1	Panel	Aspect

Press 5/∞ to select an item.

Press 2/3 to set or adjust the value.

	Color temp.
3 or	Color temp.	Low Middle High	EXIT
ENTER	RED	123
	GREEN	123
EXIT	BLUE	123
	All reset	ENTER

ENTER

Press 2/3 to select Yes or No. Then, press ENTER to execute.

Color temp.

All reset?

YesNo

Yes/No

5 ∞

Press 5/∞ to select an item.

Press 2/3 to set or adjust the value.

Options → (Refer to page 54)
Options 1
	Menu display:			15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)
	Line display:			5sec* (Line display such as “VIDEO”, “Y/C”, “PC1”, or “PC2” appears on top right of the screen for
				5 seconds when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)
	Lamp time display:
		ON*:		Displays when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.
		OFF:		Does not display when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.
	Keystone:			Press ENTER to enter the Keystone submenu.
		Keystone:			Adjust to correct the trapezoidal distortion of the projected image.
					(–80 to +120, 0*)
	Lamp control:
		Normal*:		Used as a normal lamp.
		LPC:		Lamp brightness is automatically controlled with time.
		LOC:		Lamp brightness is controlled in 7 levels (-6 to 0) irrespective of the time. This is set within the menu.
	Page 2:			Press ENTER to enter the “Page 2” submenu.
			Flip H.:		OFF* / ON (Select for upside-down hanging on the ceiling.)
			Flip V:		OFF* / ON (Select for upside-down hanging on the ceiling.)
			RS-232C [bps]:		Selectable baud rate (transmission speed). 9600 / 19200*
			Sleep time [min]:		Selectable sleep times. If no-signal condition continues for the period of
					selected time (Unite: Minutes), the projector enters the stand-by mode. 15 / 30
					/ 60 / OFF*
			Page 1:		Press ENTER to return to the “Page 1” submenu.

	Menu
	Image adj.		Menu display
	Set up		Line display
			Lamp time display
	Color temp.
			Keystone
	Options		Lamp control
	Language
	Information
	Menu	5			∞
∞	Image adj.
	Set up		English
	Color temp.		Deutsch
	Options		Español
			Italiano
	Language
	Information		Français
Menu		5			∞
Image adj.		Input		PC 1
Set up		Switcher		CH.0
Color temp.		Resolution		NTSC

	Options
3 or	Menu display	15sec	ON
ENTER Line display		5sec	OFF
	Lamp time display	ON	OFF
EXIT	Keystone	ENTER
	Lamp control	ENTER
	Page 2	ENTER

Press 5/∞ to

select an item. ENTER

Language

English

Deutsch

Español

Italiano

Français

Keystone 0

ENTER

EXIT
ENTER
Lamp control
Normal
LPC
LOC
Page 2
Flip H		OFF		ON
Flip V		OFF		ON
RS-232C [bps]		9600		19200
Sleep time [min]	15	30	60	OFF
Page 1	ENTER

FRANÇAISDEUTSHENGLISH

Language		Language for on-screen display.	→ (Refer to page 46)
	Japanese / English* / German / Spanish / Italian / French
Information → (Refer to page 56)
	Input:	Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, COMP, PC1, PC2 or DVI)
	Switcher:	Has no meaning. This display currently has no meaning, (“CH.0” is usually displayed to indicate
		that it is not being used.)
	Source:	Shows the projected image’s type of video signal.
	Lamp time:	Accumulated used hours of the light-source lamp.

* : Factory set value.

Options	Frequency H	79.9kHz
Language	Frequency V	75	Hz
Information	Lamp time	123	h

You can see the information.

Press 5/∞ to select an item.

Press 2/3 to set or adjust the value.

Note

•The display languages of the menus are set to “English” when the projector is bought. The display language can be selected from the following 6 languages:

(Japanese)”, “English (English)”, “Deutsch (German)”, “Español (Spanish)”, “Italiano (Italian)” and “Français (French)”. (Refer to page 46.) The language settings in the section are explained in “English”.

ESPAÑOLITALIANO

DLA- DLA-

1-21

40 41

G150CLU G150CLE