JVC DLA-G150CLU Remote Control Unit, G150CLE, r t, Deutsh, Français, Italiano, No.51931, Dla- Dla

Controls and Features

Controls and Features

Remote Control Unit

On the remote control, the same buttons as on the control

panel of the projector are provided except for the following buttons. For the same buttons, operation is the same in principle.

For remote control only:

DIGITAL ZOOM T/W, QUICK ALIGN., FREEZE, ZOOM T/

W, FOCUS +/–, SCREEN W/S, PC 1, PC 2, VIDEO, Y/C,

DVI, COMP.

5VIDEO button

Use this button to select a device such as a video deck connected to the AV IN terminal (VIDEO, Y/C or COMP

input terminal) of the projector. Each time you press the button, the selection alternates among Y/C, VIDEO and DVI. (Refer to page 33.)

*“Y/C”, “VIDEO” or “DVI” will be displayed on the top right of the projected image. (This function can be disabled by

the menu.)

r DIGITAL ZOOM T/W buttons

A part of image can be magnified up to four times on the screen.

Each time the T or W button is pressed, the image is enlarged or the enlarged image is reduced by a certain degree. (Refer to page 37.)

*Images which are enlarged with the digital zoom become less clear.

*Depending on the video signal source (UXGA, etc.), this button does not work.

t PC buttons

1 6 ZOOM T/W buttons

Use these buttons to select a device connected to the PC

1, PC 2 or DVI terminals. (Refer to page 33.)

No.51931

QUICK

u	ALIGN.			OPERATE		2
	W	HIDE			3
y	SCREEN	FREEZE	COMP	VIDEO		4
r t	S				5 6
	PC1	PC2	DVI	Y/C
e KEYSTONE		T	T		7
		DIGITAL	ZOOM	FOCUS
		ZOOM
w		W	W		8
		PRESET		MENU
q					p	9
		EXIT		ENTER

RM-M160 REMOTE CONTROL UNIT

1Remote control’s signal transmitter

2OPERATE button

When the projector is in the stand-by mode, press this button one second or more, and the projector is turned on, causing the OPERATE indicator to light.

Press it one second or more again, and the projector goes into the cool-down mode, then stand-by mode. (Refer to page 32.)

*The OPERATE button will not work for approximately 1 minute from when the light-source lamp is turned on. Use the button after approximately 1 minute.

Memo

While in the cool-down mode (STAND BY indicator is blinking):

Even if you press the OPERATE button, the projector is not turned on. Wait until the projector enters stand-by mode (STAND BY indicator stays lit).

3HIDE button

Use this button to turn off the image on the screen temporarily. Pressing it again makes the image to resume. (Refer to page 35.)

4FREEZE button

During projection of an image on the screen, press this button to obtain a still picture.

To restore normal projection, press it again. (Refer to page 37.)

*Depending on the video signal source (UXGA, etc.), this button does not work.

Use these buttons to adjust the projected screen size. T (Tele): The projected screen size decreases.

W (Wide):The projected screen size increases.

7FOCUS +/– buttons

Use these buttons to adjust the focus of the projected video image.

+: The focus point becomes more distant.

– : The focus point becomes nearer.

8MENU button

Use this button to enter or exit the menu mode. The main menu appears or disappears at the screen. For details, refer to “Basic Menu Operation” on page 43.

9Cursor buttons 5/∞/2/3

These buttons are used in the menu mode to select an

item or to set or adjust the value. For details, refer to “Basic Menu Operation” on page 43.

pENTER button

This button is used in the menu mode. Use to display the hierarchical menus. Also use when “ENTER” is displayed against the item on the menu screen or when the “All reset” selection is confirmed. For details, refer to “Basic Menu Operation” on page 43.

qEXIT button

This button is used in the menu mode to return to the previous menu. When the main menu is displayed, this button will cause the menu to disappear. For details, refer to “Basic Menu Operation” on page 43.

wPRESET button

This PRESET button only works as a reset button for the direct button adjustment of the KEYSTONE button of the control panel and the DIGITAL ZOOM button of the remote control. When adjusting the keystone or digital zoom (when the setting is displayed on the screen) the adjusted value is reset to that which was set when the projector was shipped from the factory. Of the menu items, this button only works for the keystone setting screen.

e KEYSTONE / buttons

Use these buttons to correct a trapezoidal distortion of the projected image. (Refer to page 35.)

* “PC 1”, “PC 2” or “DVI” will be displayed on the top right

of the projected image. (This function can be disabled

using the menu.)

ySCREEN W/S buttons

Changes the projection screen size to [4:3] or [16:9].

uQUICK ALIGN. (Quick Alignment) button

Use this button to automatically align “Horizontal and vertical position”, “Tracking” and “Phase” for the projected image.

During the automatic alignment, “Quick Alignment” appears on the screen, and disappears after alignment is finished. (Refer to page 36.)

*The “Quick Alignment” function only works when the signal is input from the input terminal of PC 1, PC 2 or DVI. It does not work when the signal is input from the VIDEO IN terminal (VIDEO, Y/C and COMP. input terminal).

CAUTION

• Automatic alignment with the quick alignment function should be carried out on a bright still-picture. This function

may not work correctly on a dark picture or motion-picture. If adjustment with this function is not satisfactory, adjust “Horizontal and vertical position”, “Tracking” and “Phase” in the menu mode.

ENGLISH
DEUTSH
FRANÇAIS
ITALIANO
	DLA- DLA-
ESPAÑOL

12

1-7

13 G150CLE G150CLU