1-76
Warning Messages
Message | Cause | Corrective action | Page |
| Displayed when the lamp control | • Arrange for a new lamp (lamp | 44, 46 |
Specifications
■ Optical mechanism system
| setting is set to LIGHT OUTPUT | unit) or replace the lamp early. |
| CONTROL MODE (LOC) or LIGHT |
|
| POWER CONTROL MODE (LPC) |
|
1000 h | and the lamp use time display is |
|
Lamp replacement | turned [ON] with the OSD menu |
|
• Displayed when the lamp use |
| |
EXIT |
| |
time exceeds 1000 hours. |
| |
|
|
* The message does not appear if |
•Projection method
•
•Projecting lens
® (Direct Drive Image Light Amplifier) method |
| ||||
|
| ||||
2.3 cm measured diagonally (1365 pixels | ⋅ 1024 pixels) | ⋅ 3 | |||
(Total number of pixels : 4,193,280) |
|
| |||
1:1 |
|
|
| ||
1.5:1 (with ±2% zooming/shift function) |
| ||||
⋅ | 1.5 zoom lens (2:1 to 3:1) (zooming function) | ||||
⋅ | 1.9 zoom lens (2.9 to 5.5:1) (zooming/shift function) |
No.51931
the lamp use time display is |
turned [OFF] with the OSD menu. |
| Displayed when the lamp control | • Arrange for a new lamp (lamp | 44, 46 |
| setting is set to LIGHT OUTPUT | unit) or replace the lamp early. |
|
| CONTROL MODE (LOC) or LIGHT |
|
|
| POWER CONTROL MODE (LPC) |
|
|
| • Appears every time the projector |
|
|
Lamp replacement | is turned on after the lamp use |
|
|
time has exceeded 1900 hours |
|
| |
EXIT |
|
| |
and until it reaches 2000 hours. |
|
| |
|
|
|
*The message is cleared by pressing any button.
| Displayed when the lamp control | • Replace with a new lamp (lamp | 44, 46 |
| setting is set to LIGHT OUTPUT | unit) and reset the lamp use time. |
|
| CONTROL MODE (LOC) or LIGHT |
|
|
| POWER CONTROL MODE (LPC) |
|
|
Warning | • When the lamp use time reaches |
|
|
Lamp replacement | 2000 hours, the word “Warning” |
|
|
EXIT | blinks on the screen. |
|
|
*To cancel this message, press the EXIT button.
However, the same message will appear every hour.
*If the power is turned off after the lamp use time has exceeded
2000 hours, the power can not be turned on again.
*When the lamp use time reaches
2010 hours, the projector is forcibly turned off and can not be turned back on again.
Memo
The message display language corresponds to the menu display language setting. This is set to “English (English)” when the projector is bought. The display language can be selected from 6 languages. (Refer to page 46.) However, the input mode (PC1, PC2, DVI, Y/C, VIDEO, COMP) and button indications (FREEZE, D.ZOOM, EXIT) are only displayed in English
irrespective of the display language setting.
The language settings in the section are explained in “English”.
69
ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH
• | Screen size | Refer to page 76. | |
|
| Refer to page 76. | |
|
| Refer to page 77. | |
|
| ||
• | Projection distance | Refer to page 76. | |
|
| Refer to page 76. | |
|
| Refer to page 77. | |
|
| ||
• | 420 W xenon lamp |
■Electrical system
• | Color system | NTSC, NTSC4.43, PAL, SECAM (Automatic switching / manual switching) | |||
• | Resolution | 1365 dots | ⋅ 1024 dots | ||
|
| 1000 TV lines (Horizontal resolution, aspect ratio 4 : 3, during video input) | |||
• | Scanning frequency | Horizontal frequency : 15 kHz ~ 105 kHz |
| ||
|
| Vertical frequency | : 50 Hz ~ 100 Hz |
| |
• | Audio power output | 1 W (monaural), 4 cm round type | ⋅ 1 |
■Input terminals
[AV | IN] |
|
|
|
|
|
• | Y/C | ⋅ 1 (for | ||||
• | VIDEO | ⋅ | 1 | (for composite video) | ||
|
| ⋅ | 3 | (for computer, DTV or video) | ||
• | Y, | Component (Y, | ||||
• | Y, BP, P R |
[PC | 1] |
|
|
|
|
• | R, G, B, H, V | ⋅ 1 (for computer) | |||
[PC | 2] |
|
|
|
|
|
| ⋅ 5 (for computer, DTV or video) | |||
• | R, B, G | Analog RGB signal |
|
|
|
• | H/C s , V | Horizontal (H) sync/composite (C S ) sync, Vertical (V) sync signal | |||
[DVI] | ⋅ | 1 | |||
[CONTROL] |
|
|
|
| |
• |
| ⋅ 1 |
|
*
• REMOTE1-line, stereo
■Output terminal
• | PC OUT | ⋅ 1 (output for display monitor) | |
• | CONTROL OUT | ⋅ 1 |
*
70