JVC DLA-G150CLU manual Message is cleared by, Pressing any button, To cancel this message, press

No.51931

1-35

Warning Messages

Message	Cause	Corrective action	Page
	• When the DIGITAL ZOOM button	• Digital-zoom function does not	13, 37
	is pressed for the video signals	work for the inputted video
	that cannot be zoomed (UXGA	signals.
	60Hz, SXGA 60Hz.), this	To use the this function, input the
	message appears for a few	video signals that can be digitally
D.ZOOM	seconds to notify that the image	zoomed.
	cannot be digitally zoomed.

*To forcibly clear the message, press the EXIT button.

		Displayed when the lamp control	• Arrange for a new lamp (lamp	44, 46
		setting is set to NORMAL MODE	unit) or replace the lamp early.
		• Appears every time the projector
		is turned on after the lamp use
		time has exceeded 900 hours and
Lamp	replacement	until it reaches 1000 hours.
		* The message is cleared by
	EXIT
		pressing any button.
		Displayed when the lamp control	• Replace with a new lamp (lamp	44, 46
		setting is set to NORMAL MODE	unit) and reset the lamp time.
		• When the lamp use time reaches
		1000 hours, the word “Warning”
	Warning	blinks on the screen.
Lamp	replacement	* To cancel this message, press
	EXIT	the EXIT button.
		However, the same message will
		appear every hour.
		* If the power is turned off after the
		lamp use time has exceeded
		1000 hours, the power can not be
		turned on again.
		* When the lamp use time reaches
		1010 hours, the projector is
		forcibly turned off and can not be
		turned back on again.

68

Warning Messages

Message	Cause	Corrective action	Page
	Displayed when the lamp control	• Arrange for a new lamp (lamp	44, 46
	setting is set to LIGHT OUTPUT	unit) or replace the lamp early.
	CONTROL MODE (LOC) or LIGHT
	POWER CONTROL MODE (LPC)
1000 h	and the lamp use time display is
Lamp replacement	turned [ON] with the OSD menu
	• Displayed when the lamp use
EXIT
	time exceeds 1000 hours.

*The message does not appear if the lamp use time display is turned [OFF] with the OSD menu.

	Displayed when the lamp control	• Arrange for a new lamp (lamp	44, 46
	setting is set to LIGHT OUTPUT	unit) or replace the lamp early.
	CONTROL MODE (LOC) or LIGHT
	POWER CONTROL MODE (LPC)
	• Appears every time the projector
Lamp replacement	is turned on after the lamp use
	time has exceeded 1900 hours
EXIT
	and until it reaches 2000 hours.

*The message is cleared by pressing any button.

	Displayed when the lamp control	• Replace with a new lamp (lamp	44, 46
	setting is set to LIGHT OUTPUT	unit) and reset the lamp use time.
	CONTROL MODE (LOC) or LIGHT
	POWER CONTROL MODE (LPC)
Warning	• When the lamp use time reaches
Lamp replacement	2000 hours, the word “Warning”
EXIT	blinks on the screen.

*To cancel this message, press the EXIT button.

However, the same message will appear every hour.

*If the power is turned off after the lamp use time has exceeded

2000 hours, the power can not be turned on again.

*When the lamp use time reaches

2010 hours, the projector is forcibly turned off and can not be turned back on again.

Memo

The message display language corresponds to the menu display language setting. This is set to “English (English)” when the projector is bought. The display language can be selected from 6 languages. (Refer to page 46.) However, the input mode (PC1, PC2, DVI, Y/C, VIDEO, COMP) and button indications (FREEZE, D.ZOOM, EXIT) are only displayed in English

irrespective of the display language setting.

The language settings in the section are explained in “English”.

69

ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH

DLA-G150CLU DLA-G150CLE