JVC DLA-G150CLE, DLA-G150CLU manual Replacing the Fuse

1-70

Replacing the Fuse

A fuse is used to protect the power source of the projector. If the fuse is blown, replace it. When the power switch is turned	on
but no power is supplied to the projector, check the fuse. If there are any unclear points, contact the dealer where you
purchased your projector, or consult the Service center.

CAUTION

•When replacing the fuse, use the same rating and type (T6.3A H 250 V). Otherwise, a fire may occur and/or the projector may be damaged.

Replacing the Light-Source Lamp

■Light-source lamp and lamp use time

The light-source lamp has a service life of approximately 1000 hours.

[Average lamp life: 1000 hours (brightness half-life)]

When the light-source lamp approaches the end of its service life, degradation progresses rapidly. In NORMAL MODE,

arrange for a new lamp (lamp unit) or replace the lamp after 900 hours. Depending on the usage conditions, the replacement time may be shorter.

(In LOC and LPC modes, the brightness of the lamp is electrically controlled and the replacement time is extended. Arrange

DLA-G150CLU DLA-G150CLE

1Turn off the main power switch and disconnect the power cord from both

the projector and the wall outlet.

In stand-by state (the STAND BY indicator lights on), place the MAIN POWER switch of OFF [ ] position.

2Loosen the fuse holder to remove it.

To loosen the fuse holder, use a Flat-end screwdriver.

for a new lamp (lamp unit) or replace the lamp after 1900 hours. Depending on the usage conditions, the replacement time may be shorter.)

If, even after adjusting the brightness or color, the video image is dark or the color is not correct, replace the lamp early. The lamp use time can be checked. Look at the “Lamp time” which is displayed with the “Information” option in the menu.

(Refer to page 40, 42.)

Contact the store from where you purchased the projector or the JVC service center for details about purchasing replacement lamps.

Replacement lamp (lamp unit) part number: BHL 5001-SU

The LAMP indicator and the message on the screen warn you that replacement of the lamp is required, as follows:

■ Projecting after the lamp has been used for more than 900 hours (NORMAL MODE)

No.51931

3Remove the fuse from the fuse holder you just removed.

4Install the new fuse (not supplied) into the fuse holder.

5Reinstall the fuse holder into the

projector.

To reinstall the fuse holder, use a Flat-end screwdriver.

Fuse holder

Flat-end screwdriver

Fuse (T6.3A H 250 V)

Fuse holder

Fuse (T6.3A H 250 V)

DEUTSHENGLISH

Accumulated used hours of the light-source lamp

When the lamp use time reaches 900 hours:

900 hours	The LAMP indicator lights on the projector.
	When	starting to project after 900	hours has been exceeded:
	“Lamp replacement” appears on the screen.
	* The message will disappear when any button is pressed.
	When	the lamp use time exceeds 1000	hours:

	The LAMP indicator blinks on the projector.
	“Lamp replacement” appears on the screen and the word “Warning”
1000 hours	blinks.

*To cancel this message, press the EXIT button. However, the same message will appear every hour.

*If the projector is put in stand-by mode or turned off after the lamp has been used for more than 1000 hours (but less than 2010 hours), it can

not be turned back on again unless the light-source lamp is replaced with a new one.

Replace with a new lamp (lamp unit) and reset the lamp time. (Refer to page 62.)

	When the lamp use time reaches 1010 hours:
	The projector is forcibly turned off.
1010 hours	The LAMP and OPERATE indicators blinks on the projector.
	* The projector can not be turned on unless the lamp (lamp unit) is
	replaced with a new one and the lamp time is reset. (Refer to

Lamp replacement

EXIT

Warning

Lamp replacement

EXIT

Fuse holder

57

ESPAÑOLITALIANO FRANÇAIS

page 62.)

Note

• If the projector is not put in stand-by mode or turned off, it can be used until 2010 hours is reached.

58