1-60
Basic Operations
■ Remote control unit | Displaying a Still Picture (FREEZE) |
|
Menu Operations
You can adjust picture quality, set functions, get information on the input video signal, etc. using the menus. From the following menu transition diagrams, you can see the overall menus and basic button operation in menu mode. Note that there are three menu modes, No signal menu mode, video menu mode and PC menu mode. When the MENU button is pressed,
QUICK
ALIGN.
| HIDE |
W |
|
SCREEN | FREEZE |
S |
|
PC1 | PC2 |
OPERATE
COMP VIDEO
DVI Y/C
FREEZE button
While projecting an image, a still picture is obtained at any time by using the FREEZE button on the remote control.
When you press the FREEZE button:
“FREEZE” appears on the screen for a few seconds and
then the still picture is shown on the screen. Refer to the FREEZE message shown on the left of this page.
* To forcibly clear “FREEZE”, press the EXIT button.
the projector enters one of these modes by judging the input signal being received.
■Menu Transition Diagram in No signal Menu Mode
This is displayed if there is no signal from the selected input terminal.
Main menu in No signal Menu Mode | Submenus in No signal Menu Mode |
DIGITAL ZOOM T/W button
PRESET button
EXIT button
| T |
KEYSTONE | DIGITAL |
ZOOM | |
| W |
| PRESET |
| EXIT |
T
ZOOM FOCUS
W
MENU
ENTER
Cursor buttons 5/∞ / 2/3
When you press the FREEZE button again.
The original image resumes.
Remote control unit | FREEZE |
Notes
Press 5/∞ to select an item.
Menu
Set up | Sync level |
Sync timing
Options
3 or ENTER
Press 5/∞ to select an item. Press 2/3 to set the value.
Set up
Sync level | Low | Std | High |
Sync timing
• During freezing, the picture sent from the signal source is |
lost. |
• If any of the inoperative buttons (“MENU”, “QUICK ALIGN.”, |
Language Information
EXIT
FREEZE message
FREEZE
FREEZE inhibit message
“KEYSTONE”) are pressed while displaying a still picture, |
“FREEZE” is displayed on the screen. |
• This function will not work with some signal sources |
(UXGA, etc). In this case, the FREEZE inhibit message
appears for a few seconds, as shown on the left. To forcibly clear this message, press the EXIT button.
Zooming a Part of the Image
(DIGITAL ZOOM T/W)
A part of the image being projected can be digitally magnified up to four times. When the DIGITAL ZOOM T or W button is
pressed, “Digital zoom” appears on the screen together with the level bar and magnifying power ( ⋅ 1.0, ⋅ 1.2, ⋅ 1.4, ⋅ 1.6, ⋅ 2.0,
∞
5
Menu
Set up
Options
Language
Information
5 ∞
English
Deutsch
Español
Italiano
Français
5 ∞
Press 5/∞ to select an item.
Language
3or
ENTER | English | ||
Deutsch | |||
|
|
| Español | |
EXIT | ||
Italiano | ||
| Français |
No.51931
FREEZE
DIGITAL ZOOM inhibit message
D.ZOOM
⋅ 2.5, ⋅ 3.2, ⋅ 4.0). When “15 sec.” is displayed in the menu, |
“Digital zoom” will appear in approximately 15 seconds. |
Digital zoom | 1.2 |
•To zoom up or zoom down, press the DIGITAL ZOOM T or W button on the remote control.
Remote control unit
T
DIGITAL
ZOOM
W
Moving the zoomed image:
While “Digital zoom” appears on the screen, you can move
the zoomed image with the cursor ( 5/∞/2/3) button on the remote control.
5: Upper part of the image will be displayed.
∞: Lower part of the image will be displayed.
2: Left side part of the image will be displayed.
3: Right side part of the image will be displayed.
Notes
•This function will not work with some signal sources (UXGA, etc). In this case, the DIGITAL ZOOM inhibit
message appears for a few seconds, as shown on the left. To forcibly clear this message, press the EXIT button.
•The quality of the zoomed image reduces in comparison with the original one.
•To return to the original size ( ⋅ 1.0) and original position, press the PRESET button while “Digital zoom” is displayed
on the screen.
ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH
Menu |
|
|
| Input | PC1 |
Set up | Switcher | CH.0 |
| ||
Options |
|
|
Language |
|
|
| Lamp time | 123 h |
Information |
|
|
■Quick Reference Guide for No signal Menu Mode
Main Menu in No signal Menu Mode |
| |||||||
|
|
|
| Set up |
| |||
|
|
|
|
|
|
| Sync level: | Low. Std*. High. |
|
|
|
|
|
| |||
|
|
|
|
|
|
| Sync timing: | |
|
|
|
|
|
|
| ||
|
|
|
| Options |
| |||
|
|
|
| |||||
|
|
|
|
|
|
| Flip H: | OFF* / ON (Select for |
|
|
|
|
|
|
| Flip V: | OFF* / ON (Select for |
|
|
|
|
|
| |||
|
|
|
|
|
|
| Selectable baud rate (transmission speed). 9600 / 19200* | |
|
|
|
|
|
| |||
|
|
|
|
|
|
| Sleep time [min]: Selectable sleep times. If | |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| (Unit: Minutes), the projector enters the |
|
|
|
| Language | Language for | |||
|
|
|
| |||||
|
|
|
|
|
|
| Japanese / English* / German / Spanish / Italian / French | |
|
|
|
|
|
| |||
|
|
|
| Information |
| |||
|
|
|
|
|
|
| Input: | Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, COMP, |
|
|
|
|
|
|
|
| PC1, PC2 or DVI) |
|
|
|
|
|
|
| Switcher: | Has no meaning. This display currently has no meaning. (“CH.0” is usually displayed to |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| indicate that it is not being used.) |
|
|
|
|
|
|
| Lamp time: | Accumulated used hours of the |
|
|
|
|
|
|
37
38