JVC DLA-G150CLU, DLA-G150CLE manual Message Cause Corrective action

No.51931

1-75

Warning Messages

The following shows the warning messages that can be displayed on the screen. When a warning message is displayed, take the corrective action described here.

Message	Cause	Corrective action	Page
	• No device is connected to the	• Connect a device to the selected	9, 11,
	input terminal.	terminal.	24 ~ 29,
	• The terminal is connected but no	• Operate the connected device	33
	signal is output from the	and output a signal.
P C 1	connected device.
	* The selected input mode (input
N o I n p u t	terminal) name is shown in the
	first line of the massage.
	• The frequency of the input video	• Input the video signals whose	22, 23,
	signal is out of range.	frequency is within the projector’s	70
	• The selected input mode (input	specifications.
	terminal) name is shown in the
P C 1	first line of the message.
Frequency of input signal is out of range .
	• Though the frequency of the input	• Input the video signals that	22, 23,
	video signal is within the	satisfies the projector’s	70
	acceptable range, other items	specifications.
	such as resolution are out of the
P C 1	projector’s specifications.
	• The selected input mode (input
S i g n a l i s n o t s u p p o r t e d .
	terminal) name is shown in the
	first line of the message.
	• When the FREEZE button is	• To release freezing, press the	12, 37
	pressed, this message appears	FREEZE button on the remote
	for a few seconds.	control.
	• When a button not acceptable is
	pressed during freezing, this
FREEZE	message appears for a few
	seconds to notify that the image is
	being frozen.
	• When the FREEZE button is	• Freeze function does not work for	12, 37
	pressed for the video signals that	the inputted video signals.
	cannot be frozen (UXGA 60Hz,	To use this function, input the
	SXGA 60Hz.), this message	video signals that can be frozen.
	appears for a few seconds to
FREEZE	notify that the image cannot be
	frozen.
	* To forcibly clear the message,
	press the EXIT button.

67

ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH

Warning Messages

Message	Cause	Corrective action	Page
	• When the DIGITAL ZOOM button	• Digital-zoom function does not	13, 37
	is pressed for the video signals	work for the inputted video
	that cannot be zoomed (UXGA	signals.
	60Hz, SXGA 60Hz.), this	To use the this function, input the
	message appears for a few	video signals that can be digitally
D.ZOOM	seconds to notify that the image	zoomed.
	cannot be digitally zoomed.

*To forcibly clear the message, press the EXIT button.

		Displayed when the lamp control	• Arrange for a new lamp (lamp	44, 46
		setting is set to NORMAL MODE	unit) or replace the lamp early.
		• Appears every time the projector
		is turned on after the lamp use
		time has exceeded 900 hours and
Lamp	replacement	until it reaches 1000 hours.
		* The message is cleared by
	EXIT
		pressing any button.
		Displayed when the lamp control	• Replace with a new lamp (lamp	44, 46
		setting is set to NORMAL MODE	unit) and reset the lamp time.
		• When the lamp use time reaches
		1000 hours, the word “Warning”
	Warning	blinks on the screen.
Lamp	replacement	* To cancel this message, press
	EXIT	the EXIT button.
		However, the same message will
		appear every hour.
		* If the power is turned off after the
		lamp use time has exceeded
		1000 hours, the power can not be
		turned on again.
		* When the lamp use time reaches
		1010 hours, the projector is
		forcibly turned off and can not be
		turned back on again.

68

DLA-G150CLU DLA-G150CLE