Menu Operations
Adjustment item | Button |
| Adjustment content | |
|
| Sets whether to clear the menu display automatically or not. | ||
Menu display | 2 or3 | 15sec* : Clears the display automatically in about 15 seconds. | ||
|
| ON | : Does not automatically clear the menu display. | |
|
|
| ||
|
| Sets whether to show the line display (Y/C, VIDEO, COMP, PC1, PC2 or DVI) on top | ||
Line display | 2 or3 | right of the screen or not when the VIDEO or PC button is pressed. | ||
5sec* | : Shows the line display for about 5 seconds. | |||
|
| |||
|
| OFF | : Does not show the line display. | |
|
|
| ||
|
| Displays the lamp use time. |
Menu Operations
Getting Information
You can get information on the input signal, accumulated used hours of
1Press the MENU button.
The main menu appears on the screen.
2 Select “Information” with the cursor button5 or ∞.
The “Information” will be displayed in the main menu. *No submenu can be selected.
|
| ON* : Displays when the lamp use time reaches 1000 hours when set in the LPC or |
Lamp time display | 2 or3 | LOC mode. |
|
| OFF : Does not display when the lamp use time reaches 1000 hours when set in the |
Video main menu
PC main menu
|
| LPC or LOC mode.3 |
|
|
| Press the ENTER button to enter the keystone submenu. | |
|
| In the keystone submenu, press | 2 or3 to correct trapezoidal distortion of the |
|
| projected image. | +128) |
Keystone | ENTER | To reset the keystone (trapezoidal distortion of the picture image) to the original | |
|
| setting (factory set value: 0), press the PRESET button when the “Keystone” | |
|
| submenu appears on the screen. |
|
|
| To exit the keystone submenu, press the EXIT button. | |
|
|
| |
|
| Press ENTER to enter the lamp control submenu. | |
|
| Normal* : Used as a normal lamp. |
|
Menu
Image adj. Setting Color temp. Options Language
Information
Input | VIDEO |
Switcher | CH.0 |
Source | NTSC |
Lamp time | 123 h |
Menu
Image adj. Setting Color temp. Options Language
Information
Input |
| PC 1 |
Switcher |
| CH.0 |
Resolution | 1280 | 1024 |
Frequency H | 79.9kHz | |
Frequency V | 75 Hz | |
Lamp time | 123 | h |
No. |
|
| LPC | : Automatically controls the power used by the lamp and increases it in | ||
|
|
| steps. When this mode is used, the brightness starts at approximately | |||
51931 |
|
|
| 70%. The decrease in brightness is slower than in “Normal” mode and this | ||
|
|
| mode is best suited when using the projector continuously for long periods | |||
Lamp control | ENTER |
| of time. |
|
| |
| * “Lamp replacement” appears on the screen when the lamp use time | |||||
|
|
| ||||
|
|
|
| exceeds 2000 hours. |
|
|
|
|
| LOC | : The brightness can be set in seven levels | ||
|
|
|
| can be set in steps, this is the mode best suited for adjusting multiple | ||
|
|
|
| screens. This setting can also be changed while the projector is being | ||
|
|
|
| used. To change the setting, choose LOC with the | 5/∞ cursors and | |
|
|
|
| choose the level with the | 2/3 cursors. |
|
|
|
|
|
|
| |
|
|
| Reverses image |
|
| |
| Flip H | 2 or3 | OFF* | : For the front method. |
|
|
|
|
| ON | : For |
| |
|
|
|
|
|
| |
|
|
| Inverses image |
|
| |
| Flip V | 2 or3 | OFF* | : For normal setup. |
|
|
|
|
| ON | : For |
| |
|
|
|
|
|
| |
|
|
| Sets the baud rate for transmission. |
|
| |
| 2 or3 | 9600 | : 9600 bps |
|
| |
|
|
| 19200* : 19200 bps |
|
| |
|
|
|
| |||
| Sleep time [min] | 2 or3 | Sets the length of sleep time which automatically brings the projector into | |||
| state. You can select one of the sleep times: 15, 30, 60 and 0 (OFF*) minutes. | |||||
|
|
| ||||
|
|
|
|
|
|
|
| * Factory set value |
|
|
|
|
|
5Press the EXIT button to return to the previous menu or press the MENU button to exit the menu mode.
Note
• Refer to “Removing the Trapezoidal Distortion of the Image” on page 35 for more details about adjusting the keystone.
55
1-69
ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH
Input: | Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO or COMP, or PC1, PC2 or DVI) |
Switcher: | This display currently has no meaning. This is reserved for future use. (“CH.0” is usually displayed to |
| indicate that it is not being used.) |
Source: | Shows the projected image’s type of video signal. (Video menu mode) |
Resolution: | Shows the resolution of the video signal being received. (PC menu mode) |
| It may not be displayed correctly with some input signals. |
Frequency H: | Shows the horizontal frequency of the video signal being received. (PC menu mode) |
Frequency V: | Shows the vertical frequency of the video signal being received. (PC menu mode) |
Lamp time: | Accumulated used hours of the |
3Press the MENU button to exit the menu mode.
56