Basic Operations
Basic Operations
■ Projector’s buttons
|
|
| STAND | BY |
|
| LAMP | TEMP |
|
|
|
| OPERATE |
|
| HIDE |
| HIDE |
|
| button |
|
|
|
|
|
| PC |
|
KEYSTONE | KEYSTONE |
|
| |
|
|
| ||
/ | buttons |
| VIDEO |
|
Turning off Image (HIDE)
Video image can be temporarily turned off.
Press the HIDE button once:
Video image instantly turn off.
Press the HIDE button again: Video image come on again.
■Remote control unit
QUICK
QUICK ALIGN. | ALIGN. | OPERATE |
|
| |
button | HIDE |
|
W | COMP VIDEO | |
| SCREEN FREEZE |
Quick Alignment Function (QUICK ALIGN.)
The Quick Alignment function automatically adjusts (sets) the screen settings of the image input from the PC1, PC2 or DVI input terminals. This can only be performed from the remote control.
| PRESET | MENU |
PRESET |
|
|
button |
|
|
EXIT |
|
|
button | EXIT | ENTER |
|
|
■ Remote control unit
Remote control unit | Projector |
HIDE |
|
| HIDE |
Note
•When the projected image input is changed, the HIDE function is canceled and the image return.
S
PC1 PC2DVI Y/C
| T | T |
|
KEYSTONE | DIGITAL | ZOOM | FOCUS |
ZOOM | |||
| W | W |
|
| PRESET |
| MENU |
| EXIT |
| ENTER |
|
|
|
While projecting an image on the screen, press the QUICK ALIGN. button on the remote control.
Quick alignment is conducted to obtain best image.
*During the automatic alignment, “Quick Alignment” appears on the screen, and then disappears when the alignment is completed.
Remote control unit
QUICK
ALIGN.
No.51931
HIDE button
KEYSTONE / buttons
PRESET button
EXIT button
QUICK ALIGN.
W
SCREEN
S
PC1
KEYSTONE
HIDE
FREEZE
PC2
T
DIGITAL
ZOOM
W
PRESET
EXIT
OPERATE
COMP VIDEO
DVI Y/C
T
ZOOM FOCUS
W
MENU
ENTER
Removing the Trapezoidal Distortion of the Image
If the image projected on the screen is distorted in trapezoid form, correct it with the KEYSTONE buttons on the projector. When the KEYSTONE button is pressed, “Keystone”
appears on the screen together with the level bar and set value
Keystone | 123 |
|
|
When you press the | KEYSTONE | button: |
|
The trapezoid form is corrected as shown in the figure.
[Screen display]
Q u i c k A l i g n m e n t
1-59
When you press the KEYSTONE button:
The top bottom inverted trapezoid form is corrected as shown in the figure.
* To cancel correction and restore the original screen, press
the PRESET button. | (Adjusted value:0) |
*Press the EXIT button to immediately remove the keystone display.
Remote control unit | Projector |
KEYSTONE | KEYSTONE |
Projected image with trapezoidal distortion
KEYSTONE
KEYSTONE
Notes
•The trapezoidal distortion (keystone) can be adjusted from the option menu. (Refer to page 54.)
•The range of the trapezoidal distortion adjustment is approximately 20° in the vertical direction.
•Interference patterns may appear on the screen when adjusting the keystone. This is not a malfunction.
•Depending on the type of signal, some noise may appear in the picture when the keystone is adjusted.
This is not a malfunction.
35
ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH
Notes
• This only works for the signals input from the PC1, PC2 or DVI input terminals. It does not work for the signals input from the AV IN terminal (VIDEO, Y/C or COMP input terminal).
• The quick alignment function is used to automatically adjust the “Horizontal and vertical position”, “Phase” and “Tracking” of the projected image.
• When using the quick alignment function to automatically adjust the image, use a bright,
36