JVC DLA-G150CLU manual Hor Pixels Ver Lines KHz PC system PC98, 640 350 37.86, 640 400 24.83 56.42

Connecting to Various Devices

■Allowable input signals

			Horizontal res-	Vertical resolu- Horizontal fre-		Vertical fre-
	Signal		olution	tion	quency	quency
			Hor [Pixels]	Ver [Lines]	H [kHz]	V [Hz]
PC system	PC98	VESA350	640	350	37.86	84.13
	PC/AT	PC98	640	400	24.83	56.42
	DOS/V	VGA 60Hz*	640	480	31.47	59.94

Connecting to Various Devices

Connecting to Video Devices

Before connection, be sure to turn off both the projector and video device.

•Read thoroughly the manual that comes with each video device.

•Use the supplied video cable. An video cable with an S-video (Y/C) terminal is not supplied.

DVI*	VGA 72Hz*	640	480	37.86	72.81
	VGA 75Hz*	640	480	37.50	75.00
	VGA 85Hz*	640	480	43.27	85.01
	SVGA 56Hz*	800	600	35.16	56.25
	SVGA 60Hz*	800	600	37.88	60.32
	SVGA 72Hz*	800	600	48.08	72.19
	SVGA 75Hz*	800	600	46.88	75.00
	SVGA 85Hz*	800	600	53.67	85.06
	XGA 43Hz*	1024	768/2	35.52	43.48
	XGA 60Hz*	1024	768	48.36	60.00
	XGA 70Hz*	1024	768	56.48	70.07
No.	XGA 75Hz*	1024	768	60.02	75.03
	XGA 85Hz*	1024	768	68.68	85.00
	SXGA 43Hz*	1280	1024/2	46.43	43.44

R	Y
	Y/C
G	P B /B-Y
	VIDEO
B	P R /R-Y
	REMOTE
H
V
IN
IN	OUT

BNC-RCA conversion plug (accessory)

To VIDEO

Video cable (accessory)

To AV IN

To Y/C

S-video cable (separately available)

51931			SXGA 60Hz*	1280	1024	63.98	60.02
			SXGA 75Hz*	1280	1024	79.98	75.03
			SXGA 85Hz*	1280	1024	91.15	85.02
			UXGA 60Hz	1600	1200	75.00	60.00
		Mac	MAC13	640	480	35.00	66.67
			MAC16	832	624	49.73	74.55
			MAC19	1024	768	60.24	74.93
			MAC21	1152	870	68.68	75.06
	Video system	Video	HDTV (1035i) 60Hz			33.75	60.00
			HDTV (1035i) 59Hz			33.72	59.94
			480p	720	483	31.47	59.94
			720p 60Hz	1280	720	45.00	60.00
			720p 59Hz	1280	720	44.96	59.94
			1080i 60Hz	1920	1080/2	33.75	60.00
			1080i 59Hz	1920	1080/2	33.72	59.94
			1080 24sF	1920	1080	27.00	24.00
			NTSC			15.734	60
			PAL			15.625	50
			SECAM			15.625	50

* A signal that can be input by DVI (V-sync 85Hz is not supported.)

Notes

•The resolution for the input signals is listed in the above table.

•Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.

•When a signal other than listed above is input, the image could be partially erased or an unneeded fold-over image could appear.

•Some signals other than listed above can be displayed. But they may require adjustment.

•Even some of the signals listed above may require adjustment depending on the video board used.

•Composite sync (C S ) and G on Sync signals cannot be handled depending on the devices connected.

•The VGA signal of the PC system could be displayed in 480p mode of the VIDEO system. (In this case, the projector enters video menu mode when the MENU button is pressed.)

23

1-53

ESPAÑOLITALIANO FRANÇAISDEUTSHENGLISH

Video devices

•VCR (Video cassette recorder)

•Laser videodisc player

•Camcorder

Notes

•Connect a composite image signal output device or Y/C (S-video) image output device.

•When connecting the S-video cable, refer to “How to attach the ferrite core” on page 29.

Memo

•When connecting a video device, use a TBC along with it, or one which has a built-in TBC.

•Use of an extension cable to connect a video device and the projector could cause video degradation.

•When a signal with much jitter is reproduced on a VCR, or special-effect playback is performed, the upper part of the image or the image itself may be erased or distorted.

24

DLA-G150CLU DLA-G150CLE