JVC DR-MV1B manual On The Front Display Panel, Link Functions DVD Deck Only

Filename [DR-MV1SEK_04Name.fm]
DR-MV1SEK_00.book Page 21 Thursday, April 15, 2004 3:30 PM	Masterpage:Right+
	INITIAL SETTINGS EN 21

Results Of Auto Set Up/Preset Download Appearing	INFORMATION
On The Front Display Panel	Just Clock
	Your unit is equipped with the Just Clock function which provides
If both Auto Channel Set and	accurate time keeping through automatic adjustments at regular
	intervals, by reading data from a PDC signal. If you want to take
Auto Clock Set have been
	advantage of this function, simply set it to “ON”. ( pg. 86)
performed successfully, the
correct current time is displayed.
Turn on the TV and select its AV mode, then make sure that all	If you have any difficulty with the above procedures call the JVC
necessary stations have been stored in the unit’s memory by using	Customer Service Hot Line on 0870 330 5000
the PR +/– button(s).

●If station names (ID –  pg. 100) have also been stored in the unit’s memory, the station name will be displayed at the top right corner of the TV screen for about 5 seconds when the unit is tuned to a different station.

●If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 84 – 85.

If Auto Channel Set has succeeded but Auto Clock Set

has not, “PR 1” (channel position) is displayed.

OR

If both Auto Channel Set and Auto Clock Set have failed, “– –:– –” is displayed.

ATurn on the TV and select its AV mode, then make sure that all necessary stations have been stored in the unit’s memory by using the PR +/– button(s).

● If station names (ID –  pg. 100) have also been stored in the unit’s memory, the station name will be displayed at the top right corner of the TV screen for about 5 seconds when the unit is tuned to a different station.

● If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 84 – 85.

B Perform “Clock Set” on page 86.

ATTENTION:

After making sure the cables are connected properly, turn off the unit’s power once, then turn the unit’s power back on again.

Perform “Auto Set Up” on page 19 or “Preset Download” on page 20 again.

IMPORTANT:

●To check if the Guide Program numbers have been set correctly, perform the VIDEO Plus+ Timer Programming. ( pg. 45, 56)

●In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the VIDEO Plus+ system, the unit will record a TV programme of a different station. When programming the timer using the VIDEO Plus+ system, be sure to check the desired channel is selected correctly. ( pg. 45, 56)

●Your unit memorises all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture. ( pg. 85, “Delete A Channel”)

T-V Link Functions (DVD Deck Only)

When you connect the unit to your TV via a fully-wired 21-pin SCART cable ( pg. 18), the following functions are available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual of your TV.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically whenever you start playback.

For details, refer to the instruction manual of your TV.

Unit Auto Standby

You can use your TV’s remote control to turn off the unit. For details, refer to the instruction manual of your TV.

Direct Rec

You can easily start recording the programme that you are watching on your TV. When you use this function, set “DIRECT REC” to “ON”. ( pg. 81)

Page 21

April 15, 2004 3:19 pm