JVC DR-MV1B DV Dubbing (DVD Deck Only)

Masterpage:Right+
EN 71
Filename [DR-MV1SEK_09Editing.fm]
Page 71 April 15, 2004 3:18 pm
EDITING
You can dub programmes from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
1Connect a camcorder or DV equipment to the DV IN connector
on the unit’s front panel.
2Load a DVD-RAM/RW/R disc on the unit.
3Press PR +/– to set the channel to “DV DUBBING”.
●The “DV DUBBING” controller appears on the TV screen.
●If “ ” does not appear on the “DV DUBBING” controller, make
sure the DV equipment is connected correctly.
4Press we to select , then press ENTER.
5Press rt to select the desired
sound track, then press ENTER.
AUDIO 1: Select this to record the
original stereo sound played
back on the connected DV
equipment.
AUDIO 2: Select this to record the
dubbed stereo sound played
back on the connected DV
equipment.
MIX: Select this to record the sound of both “AUDIO 1” and
“AUDIO 2”.
●Note that this selection is not available when the source programme
is recorded in 16BIT (48 kHz) mode.
6Press REC MODE repeatedly to set the recording mode.
7Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9
●To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
●To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
●To change the playback direction, press 3 or 5.
8Press we to select , then press ENTER. The
dubbing starts.
●Playback on the external DV equipment and recording on the unit
should start simultaneously.
●When the playback from the beginning is not possible, the “DV
DUBBING” controller cannot be used. Perform dubbing without using
the “DV DUBBING” controller. (墌below)
●To pause dubbing, press we to select , then press
ENTER. Both the unit and the external DV equipment pause dubbing.
Pressing 9 on the unit also works the same way.
●To clear the “DV DUBBING” controller from the TV screen, press ON
SCREEN.
9Press 8 on the remote control to stop dubbing.
●Both the unit and the external DV equipment stop dubbing.
NOTES:
●Dubbing copyright guarded programmes is not possible.
●Original DV informations such as the recording date and time are not
recorded.
●The superimposed indication during the operation or dubbing is not
recorded.
●It is not possible to perform dubbing when “VCR]” lights up on the
unit. Press VCR] so that “VCR]” lights off.
Performing dubbing without using the “DV DUBBING”
controller
APress PR +/– to set the channel to “DV DUBBING”.
BPress REC MODE repeatedly to set the recording mode.
CStart playback on the external DV equipment slightly before the
actual point from where you wish to start dubbing.
DPress 7 on the unit to start recording. Or press and hold 7 and
press 4 on the remote control. The dubbing starts.
EWhen the dubbing ends, press 8 on the unit, then stop
playback on the external DV equipment.
DV Dubbing (DVD Deck Only)
NOTE:
When you connect a PC to the DV IN connector, we do not assure
the normal operation of this unit.
VPS/PDC VCD
HDD DVD
DVHS
BS
+
STANDBY/ON
DVD
S-VIDEO VIDEO (MONO) L - AUDIO - R
VCR/DVD VCR
REMAIN
REC MODE SLOW
<< >>
PR DV IN
SAT
DVD
DVD DVDVCR DUB
F-1
DV IN connector
DV cable
(VC-VDV 204U)
(not provided)
Camcorder
DV connector
Your unit
DV equipment
DR-MV1SEK_00.book Page 71 Thursday, April 15, 2004 3:30 PM