Filename [DR-MV1SEK_10Subsidiary.fm]

 

DR-MV1SEK_00.book Page 92 Thursday, April 15, 2004 3:30 PM

Masterpage:Left+

 

92 EN TROUBLESHOOTING

Timer Recording (DVD Deck)

Timer programming cannot be made.

Date and time is not correct.

]Set date and time correctly. ( pg. 86)

The timer is not engaged.

]Press DVD TIMER (#) and confirm that the DVD timer lamp lights up on the unit.

Timer recording is in progress.

]Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

Timer programming recording does not start.

Date and time is not correct.

]Set date and time correctly. ( pg. 86)

The timer is not engaged.

]Press DVD TIMER (#) and confirm that the DVD timer lamp lights up on the unit.

There is a power outage while the DVD deck is in the timer standby mode.

]The unit does not enter timer standby mode automatically when the power is restored to the unit. Engage the timer standby mode again.

VIDEO Plus+ Timer Programming cannot be made.

Date and time set on the unit is not correct. ]Set date and time correctly. ( pg. 86)

The channel position does not correspond to that in the receiving area.

]Set the correct channel position for the receiving broadcast. ( pg. 83)

Automatic Satellite Programme Recording does not start.

The satellite receiver is not connected properly to this unit. ]Connect the satellite receiver to the L-2 IN/DECODER

connector properly. ( pg. 50)

On the front display panel, “– –:– –” appears.

Power failure occurred.

]Set date and time correctly. ( pg. 86)

“PROGRAM FULL” appears on the TV screen during timer programming.

Eight programmes have already been timer programmed. ]Clear unnecessary programmes on the unit, then try timer

programming again. ( pg. 49)

The disc space does not increase when recorded programmes are cleared.

The PC’s data recorded on a DVD-RAM drive cannot be cleared on this unit.

]Format the disc. (When the disc is soiled, wipe the disc with a soft dry cloth before formatting.) ( pg. 11, 87)

Timer Recording (VCR Deck)

Timer programming cannot be made.

Date and time is not correct.

]Set date and time correctly. ( pg. 86)

The timer is not engaged.

]Press VCR TIMER (#) and confirm that the VCR timer lamp lights up on the unit.

Timer recording is in progress.

]Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

Timer programming recording does not start.

Date and time is not correct.

]Set date and time correctly. ( pg. 86)

The timer is not engaged.

]Press VCR TIMER (#) and confirm that the VCR timer lamp lights up on the unit.

The VCR Timer lamp on the unit won’t stop blinking.

The timer is engaged but there’s no cassette loaded. ]Load a cassette with the record safety tab intact.

The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or

insert a cassette with the record safety tab intact.

The tape is automatically ejected, then the unit is shut off.

The end of the tape was reached during timer recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

The end of the tape was reached during Instant Timer Recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

VIDEO Plus+ Timer Programming cannot be made.

Date and time set on the unit is not correct. ]Set date and time correctly. ( pg. 86)

The channel position does not correspond to that in the

receiving area.

]Set the correct channel position for the receiving broadcast. ( pg. 84)

The VIDEO Plus+ system does not timer-record properly.

The unit’s channel positions have been set incorrectly. ]Refer to “VIDEO Plus+® System Setup” ( pg. 83) and re-

perform the procedure.

Page 92

April 15, 2004 3:21 pm

Page 92
Image 92
JVC DR-MV1B Timer Recording DVD Deck, Timer Recording VCR Deck, Power failure occurred Set date and time correctly.  pg