JVC DR-MV1B manual Manual Timer Programming, PDC Recording

Filename [DR-MV1SEK_06DVD Operation2.fm]
DR-MV1SEK_00.book Page 46 Thursday, April 15, 2004 3:30 PM	Masterpage:Left+

46 EN OPERATIONS ON DVD DECK

Manual Timer Programming				10 Press ENTER to access the Programme Confirmation screen.
				11 Press ENTER to complete timer programming.
				● To programme another timer, repeat steps 3 – 11.
				12 Press DVD TIMER (#) to engage the unit’s timer mode. The
				DVD timer lamp lights up on the unit and the VCR deck is
You can programme this unit to timer-record as many as				automatically selected. Press 1 to turn off the unit. When the
				VCR deck is in timer standby mode, the unit is automatically turned
8 programmes.				off.
If you do not know the PlusCode number for the programme you				#
wish to record, use the following procedure to set your unit to				● To disengage the timer mode, press DVD TIMER ( ) again.
				NOTES:
timer-record the programme.
				● When two successive programmes are recorded on a DVD-RW disc
● Make sure that the unit’s built-in clock is set properly.				with Manual Timer Programming function, the beginning of the
				second one may be left off the recording.
● Turn on the unit.
				● If the copy limited programme is received during timer-recording, the
● Turn on the TV and select the AV mode.
				unit enters Record Pause mode. Recording starts again if it is
● Slide the TV/CABLE/SAT/DVD switch to DVD.
				switched to a recordable broadcast during the time you programmed.
				Satellite Receiver Users
#			SAT	To timer-record a satellite broadcast using Manual Timer
DVD TIMER ( )				Programming:
VCR/DVD
	2	3		A Perform “Satellite Receiver Control Setting (DVD Deck Only)”
1
4	5	6
				( pg. 23).
7	8	9	AUX
	0			B Perform “Manual Timer Programming” ( pg. 46). In step 8,
PROG/CHECK			DISPLAY
				press AUX to change “TV PROG” to “SAT”. Then press rt to
			rtw e	enter the channel position for the satellite broadcast. In step 9,
ENTER				you cannot set “VPS/PDC” to “ON”.
				C Leave the satellite receiver’s power on.

1 Load a recordable disc.

2 Press VCR/DVD repeatedly so that the DVD lamp lights up on the unit.

3 Press PROG/CHECK to access the Programme Check screen.

●When “PROGRAMME FULL

DELETE UNWANTED TIMER PROGRAMME” appears on the TV screen, you need to cancel some of the reserved programmes. ( pg. 49)

4 Press rt to select “NEW TIMER PROGRAMME”, then press ENTER. The programme screen appears.

5 Press rt to set the desired date.

● The current date appears on the TV screen. The date you enter appears in its place.

6 Press w e to select “START”, then press rt to set the desired start time.

●Each press of rt advances/goes back the start time in 1-min. increments.

●To advance/go back the start time in 30-min. increments, press and hold rt.

7 Press w e to select “STOP”, then press rt to set the desired stop time.

●Each press of rt advances/goes back the stop time in 1-min. increments.

●To advance/go back the stop time in 30-min. increments, press and hold rt.

8 Press w e to select “TV PROG”, then press rt to select the desired channel.

9 Set the other recording options as required.

●Refer to step 6 in “VIDEO Plus+® Timer Programming” ( pg. 45).

Page 46

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your unit and have precedence over the advertised times which you may have preset into the timer. This means that your unit will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your unit will not start recording if PDC has been selected. Be sure to set PDC to “OFF” if PDC is not available on your selected channel. (See step 6 on page 45.)

NOTES:

●When you use Manual Timer Programming, set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

●PDC recording is also possible when a satellite receiver or a cable system is connected to L-2 IN/DECODER connector on your unit.

●PDC recording is also possible via the L-1 IN/OUT connector.

April 15, 2004 3:30 pm