JVC DR-MV1B manual Off, April 22, 2004 509 pm

Filename [DR-MV1SEK_07VCR Operation.fm]
DR-MV1SEK_07VCR Operation.fm Page 57 Thursday, April 22, 2004 5:10 PM	Masterpage:Right+
	OPERATIONS ON VCR DECK EN 57

9 Press REC MODE to select the desired recording mode. Or

Manual Timer Programmingpress w e to select “SP/LP”, then press rt to select the desired recording mode.

You can programme this unit to timer-record as many as				10Press the number keys to set “VPS/PDC” to “ON” or “OFF”.
8 programmes.
				* VPS (Video Programme System) recording is not currently available
If you do not know the PlusCode number for the programme you
wish to record, use the following procedure to set your unit to				in the U.K. and not possible with this unit.
				11 Press ENTER to access the Programme Check screen.
timer-record the programme.
● Make sure that the unit’s built-in clock is set properly.				12 Press PROG/CHECK to complete timer programming.
				“PROGRAM COMPLETED” appears on the TV screen for about 5
● Turn on the unit.
				seconds, then the normal screen appears. If “PROGRAM
● Turn on the TV and select the AV mode.
				OVERLAPPED” appears on the TV screen, see page 58.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
				● To programme another timer, repeat steps 3 – 12.
				13 Press VCR TIMER (#) to engage the unit’s timer mode. The
				VCR timer lamp lights up on the unit and the DVD deck is
VCR TIMER (#)			SAT	automatically selected. Press 1 to turn off the unit. When the
VCR/DVD	2	3		DVD deck is in timer standby mode, the unit is automatically turned
1				off.
4	5	6	0 – 9
7	8	9		● To disengage the timer mode, press VCR TIMER (#) again.
PROG/CHECK	0		DISPLAY	NOTES:
				● To Timer-Record Weekly Or Daily Serials:
ENTER			rtw e	— anytime during steps 7 through 9, press number key “9” for
				weekly serials or number key “8” for daily serials (Monday – Friday).
				Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
				button again makes the corresponding indication disappear.
				● You can programme this unit to timer-record as many as 8
REC MODE				programmes. If you try to programme the unit to record a ninth,
				“PROGRAMME FULL” appears on the TV screen. To record the extra
				programme, you must first cancel any unnecessary programmes.
				( pg. 58)
				● In case of a power failure after programming, the unit’s memory
				backup keeps your selections for approximately 5 seconds.
1 Load a cassette with the record safety tab intact.				● Programmes that start after midnight must have the next day’s date.
				● To record the programmes received by satellite receiver, record on
2 Press VCR/DVD repeatedly so that the VCR lamp lights up on				the DVD discs. For details, refer to “Manual Timer Programming”
				( pg. 46).

the unit.

3Press PROG/CHECK to access the

Programme Check screen.

4 Press rt to select the blank number, then press ENTER. The programme screen appears.

5 Press w e to select “START”, then press rt to set the desired start time.

● Each press of rt advances/goes back the start time in 1-min. increments.

● To advance/go back the start time in 30-min. increments, press and hold rt.

6 Press w e to select “STOP”, then press rt to set the desired stop time.

●Each press of rt advances/goes back the stop time in 1-min. increments.

●To advance/go back the stop time in 30-min. increments, press and hold rt.

7 Press w e to select “DATE”, then press rt to set the desired date.

●The current date appears on the TV screen. The date you enter appears in its place.

8 Press w e to select “TV PROG”, then press rt to select the desired channel.

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your unit and have precedence over the advertised times which you may have preset into the timer. This means that your unit will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your unit will not start recording if PDC has been selected. Be sure to set PDC to “OFF” if PDC is not available on your selected channel. (See step 7 on page 56.)

NOTES:

●When you use Manual Timer Programming, set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

●PDC recording is not possible when a satellite receiver or a cable system is connected to L-2 IN/DECODER connector on your unit.

●PDC recording is also possible via the L-1 IN/OUT connector.

Page 57

April 22, 2004 5:09 pm