JVC DR-MV1B manual According to your preference. Normally select Auto, Containing a lot of noise

Filename [DR-MV1SEK_10Subsidiary.fm]
DR-MV1SEK_00.book Page 82 Thursday, April 15, 2004 3:30 PM	Masterpage:Left+

82 EN SUBSIDIARY SETTINGS

Mode Set (VCR Deck)			8 PICTURE CONTROL — AUTO / EDIT / SOFT / SHARP
			This feature helps you to adjust the playback picture quality
● Turn on the unit.			according to your preference. Normally select “AUTO”.
			AUTO: Picture quality is adjusted automatically.
● Turn on the TV and select the AV mode.			EDIT: Minimizes picture degradation during editing (recording and
● Slide the TV/CABLE/SAT/DVD switch to DVD.
			playback).
			SOFT: Reduces image coarseness when viewing overplayed tapes
			containing a lot of noise.
VCR/DVD		SAT	SHARP: Clearer, sharper-edged picture when viewing images with
			lots of flat, same-coloured surfaces such as cartoons.
1	2	3	NOTES:
4	5	6
7	8	9	● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will
	0		not change until you select another mode.
			● When you select “EDIT” to dub tapes, be sure to select “NORM” after
ENTER		rtw e	you finish dubbing the tapes.
			● When “B.E.S.T.” is “OFF”, “PICTURE CONTROL” switches
SET UP			automatically from “AUTO” to “NORM”.

You can change various mode settings on the Function Set screen. To change the settings of these modes, find the desired mode in the menu (for details on each menu, see page 82), then follow the procedure below.

1 Press VCR/DVD repeatedly so that the VCR lamp lights up on the unit.

2 Press SET UP to access the Function Set screen.

3 Press rt to select the item you want to change, then press ENTER or e to select the desired mode.

4 Press SET UP to complete the setting.

*The boldface settings below indicate the settings at your purchase.

8B.E.S.T. — ON / OFF

You can set the B.E.S.T. (Biconditional Equalised Signal Tracking) system to “ON” or “OFF”. ( pg. 55)

NOTES:

●When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.

●When watching a rental tape or one recorded on another video recorder, or when using this unit as the player for editing, set B.E.S.T. to your preference.

●The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

●The B.E.S.T. system does not work while Automatic Satellite Programme Recording is in progress. ( pg. 50)

●In the case of timer recordings, the B.E.S.T. system works before recording is initiated.

●Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re-performed.

●Pressing the unit’s 7 button while “BEST” is displayed does not start Instant Timer Recording. ( pg. 55)

8O.S.D. — AUTO / OFF

When this function is set to “AUTO”, various operational indicators appear on the TV screen. Messages appear in the selected language. ( pg. 22)

NOTES:

●Even when “O.S.D.” is set to “OFF”, you can display the various operational indicators by pressing ON SCREEN. To clear the operational indicators, press ON SCREEN again.

●When you use this unit as the source player for editing, be sure to set “O.S.D.” to “OFF” before starting.

●During playback, the operation mode indicators may be disturbed depending on the type of tape being used.

8AUTO SP]LP TIMER — ON / OFF

When this function is set to “ON”, the unit automatically switches to LP mode to allow complete recording if there is not enough tape to record the entire programme while timer-recording in SP mode.

For Example:

Recording a programme of 140 minutes in length onto a 120- minute tape

Approximately 110 minutes	Approximately 30 minutes
SP mode	LP mode

Total 140 minutes

Make sure you set this function to “ON”, before the timer-recording starts.

NOTES:

●If you have programmed the unit to timer-record 2 or more programmes, the second programme and those thereafter may not fit on the tape if you set “AUTO SP]LP TIMER” to “ON”. In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming.

●In order to ensure that the recording fits on the tape, this feature may leave a slight non-recorded section at the end of the tape.

●There may be some noise and sound disturbance at the point on the tape where the unit switches from SP to LP mode.

●The Auto SP]LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120

Page 82

April 15, 2004 3:21 pm