Filename [DR-MV1SEK_09Editing.fm]
Masterpage:Left+

74 EN

Page 74 April 15, 2004 3:18 pm
EDITING

L-1 Output And L-1 Input Setting

The L-1 IN/OUT connector accepts and delivers either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set “L-1
OUTPUT” and “L-1 INPUT” to the appropriate mode depending on
the type of appliance connected to the unit’s L-1 IN/OUT
connector.
1Press SET UP to access the Main Menu screen.
2Press we to select “FUNCTION SET UP”, then press ENTER.
3Press we to select “VIDEO IN/
OUT”, then press ENTER.
4Press rt to select “L-1
OUTPUT” or “L-1 INPUT”, then
press ENTER.
5Press rt to select the
appropriate setting, then press
ENTER.
6Press SET UP to complete the
setting.
NOTES:
●If “L-1 INPUT” or “L-1 OUTPUT”
is set to “S-VIDEO”, it is not
possible to output colour signals correctly from the VCR deck.
●When the progressive mode is set, be sure to set “L-1 OUTPUT”
to “COMPONENT”. (墌pg. 74)
●If “L-1 OUTPUT” is not set to “COMPONENT”, it is not possible
to output images from the COMPONENT VIDEO OUT
connector.
*The boldface settings below indicate the settings at your purchase.
8L-1 OUTPUT — SCART VIDEO / SCART S-VIDEO / SCART
RGB / COMPONENT
SCART VIDEO: If a connected appliance’s input is compatible only
with regular video signals, set to “SCART VIDEO”.
SCART S-VIDEO: If a connected appliance’s input is compatible
with Y/C signals, set to “SCART S-VIDEO”. You can obtain high-
quality picture. (For connection, be sure to use a 21-pin SCART
cable that is compatible with the Y/C signal.)
SCART RGB: If a connected appliance’s input is compatible with
RGB signals, set to “SCART RGB”. You can obtain a high-quality
RGB picture.
COMPONENT: If a connected appliance’s input is compatible with
Y/PB/PR signals, set to “COMPONENT”. You can obtain a high-
quality Y/PB/PR picture. Switch the TV to the input that you can
watch component video pictures.
8L-1 INPUT — VIDEO / S-VIDEO
VIDEO: If a connected appliance’s output is compatible only with
regular video signals, set to “VIDEO”.
S-VIDEO: If a connected appliance’s output is compatible with Y/C
signals, set to “S-VIDEO”. You can obtain a high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
NOTES:
●If “L-1 OUTPUT” is set to “SCART S-VIDEO”, “SCART RGB” or
“COMPONENT”, it is not possible to set “L-1 INPUT” to “S-VIDEO”.
●If “L-2 SELECT” is set to “DECODER”, it is not possible to set “L-1
INPUT” to “S-VIDEO”.
●If “L-2 SELECT” is set to “DECODER”, it is only possible to set “L-1
OUTPUT” to “SCART VIDEO”.
●Component video signals are not output from the L-1 IN/OUT
connector.
●When Progressive scan mode is engaged, it is not possible to select
the setting of “L-1 OUTPUT”. (墌pg. 74)

L-2 Select Setting

Set “L-2 SELECT” to the appropriate mode depending on the type
of appliance connected to the unit’s L-2 IN/DECODER connector.
1Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting” on
the left column.
2Press rt to select “L-2 SELECT”, then press ENTER.
3Press rt to select the
appropriate setting, then press
ENTER.
4Press SET UP to complete the
setting.
NOTES:
●If “L-2 SELECT” is set to
“S-VIDEO”, it is not possible to
output colour signals correctly from the VCR deck.
●If “L-2 SELECT” is set to “DECODER”, only the DVD deck
operates properly.
*The boldface settings below indicate the settings at your purchase.
8L-2 SELECT — VIDEO / S-VIDEO / SAT VIDEO / SAT
S-VIDEO / DECODER
Select “VIDEO” or “S-VIDEO” to use this unit as the recording deck
with the player connected to the L-2 IN/DECODER connector, or to
use the satellite receiver connected to the L-2 IN/DECODER
connector.
VIDEO: If a connected appliance’s output is compatible only with
regular video signals, set to “VIDEO”.
S-VIDEO: If a connected appliance’s output is compatible with Y/C
signals, set to “S-VIDEO”. You can obtain high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
Select “SAT VIDEO” or “SAT S-VIDEO” to view a satellite
programme with the TV set while the unit is turned off. (墌pg. 78)
SAT VIDEO: If a connected satellite receiver’s output is compatible
only with regular video signals, set to “SAT VIDEO”.
SAT S-VIDEO: If a connected satellite receiver’s output is
compatible with Y/C signals, set to “SAT S-VIDEO”. You can
obtain a high-quality S-VHS picture. (For connection, be sure to
use a 21-pin SCART cable that is compatible with the Y/C signal.)
DECODER: To use a decoder connected to the L-2 IN/DECODER
connector.

Output/Input Set

●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
1
4
7
2
5
8
0
3
6
9
VCR/DVD
rtw e
ENTER
SET UP
SAT
DR-MV1SEK_00.book Page 74 Thursday, April 15, 2004 3:30 PM