JVC DR-MV1B manual Manual Channel Set, View the Confirmation screen. Scan Completed is

Filename [DR-MV1SEK_10Subsidiary.fm]
DR-MV1SEK_10Subsidiary.fm Page 84 Thursday, April 22, 2004 5:13 PM	Masterpage:Left+

84 EN SUBSIDIARY SETTINGS

4 View the Confirmation screen. “SCAN COMPLETED” is	Manual Channel Set
displayed on the TV screen. Press “OK”.

5 Press SET UP to complete the setting.

●When Auto Channel Set is completed, “PLEASE WAIT” will be displayed for about 90 seconds, since channel data is exchanged between the DVD deck and the VHS deck. No operations will be done during this time.

●Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 84 – 85 for the procedures.

●Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

IMPORTANT:

●In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. When the Guide Programme numbers are not set properly, the programme that you do not intended to record will be timer-recorded by the VIDEO Plus+ system of the unit. When programming the timer using the VIDEO Plus+ system, be sure to check the desired channel is selected correctly. ( pg. 45, 56)

●Your unit memorises all receivable stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture from the list. ( pg. 85, “Delete A Channel”)

Store channels that were not stored during Auto Set Up

( pg. 19), Preset Download ( pg. 20) or Auto Channel Set ( pg. 83).

VCR/DVD		SAT
1	2	3
4	5	6
7	8	9
	0

ENTER	rtw e
SET UP

NOTES:

●Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to “Fine-Tuning Channels Already Stored” ( pg. 85).

●If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED –NO SIGNAL–” appears on the TV screen in step 4. In such a case, make sure of the aerial connection and press ENTER; Auto Channel Set will start again.

1 Press SET UP to access the Main Menu screen.

2 Press w e to select “INITIAL SET UP”, then press ENTER.

3 Press w e to select “MANUAL CH SET”, then press ENTER. The Confirmation screen appears.

4 Press rt w e to select a	(Example) To store in position 6.
blank position in which you want to
store a channel, then press
ENTER twice. The Manual
Channel Set screen appears.

5 Press rt to select “BAND”, then press ENTER.

The programme currently received on the selected channel position appears behind the confirmation screen.

Page 84

6 Press rt to change the band between CH (regular) and CC (cable), then press ENTER.

7 Press rt to select “CH”, then press ENTER.

8 Press rt to input the channel number you want to store.

●To enter the registered station name ( pg. 100), press rt to

select “ID”, then press ENTER. Press rt.

●For fine tuning adjustment, press rt to select “FINE”, then press ENTER. Press rt to perform fine-tuning.

●When “L-2 SELECT” is set to “VIDEO”, “S-VIDEO”, “SAT VIDEO” or “SAT S-VIDEO”, the “DECODER” setting cannot be changed.

( pg. 74)

9 Press ENTER to enter new channel information. The Confirmation screen appears.

●Repeat steps 4 – 9 as necessary.

10 Press SET UP to close the Confirmation screen.

●When Auto Channel Set is completed, “PLEASE WAIT” will be displayed for about 90 seconds, since channel data is exchanged between the DVD deck and the VHS deck. No operations will be done during this time.

●To change positions, see “Change Station Channel Position” ( pg. 85).

●If you wish to set station names other than the ones registered in your unit, see “Set Stations (B)” ( pg. 85).

ATTENTION:

Guide Program numbers are not set when channels are stored manually. ( pg. 83, “VIDEO Plus+® System Setup”)

April 22, 2004 5:12 pm