JVC DR-MV1B manual Mode Set DVD Deck, Filename DR-MV1SEK10Subsidiary.fm, Utility  pg, Others  pg

Press w e to select “FUNCTION SET UP”, then press ENTER.

Filename [DR-MV1SEK_10Subsidiary.fm]
DR-MV1SEK_00.book Page 80 Thursday, April 15, 2004 3:30 PM	Masterpage:Left0

80 EN SUBSIDIARY SETTINGS

Mode Set (DVD Deck)

* The boldface settings below indicate the settings at your purchase.

AUDIO OUTPUT

●Turn on the unit.

●Turn on the TV and select the AV mode.

●Slide the TV/CABLE/SAT/DVD switch to DVD.

VCR/DVD		SAT
1	2	3
4	5	6
7	8	9
	0

ENTER	rtw e
SET UP

8DIGITAL AUDIO OUT — DOLBY DIGITAL/PCM / STREAM/

PCM / PCM ONLY

Set to the appropriate mode according to the type of the device connected to DIGITAL AUDIO OUT connector.

DOLBY DIGITAL/PCM: Select this when you connect the digital input connector of a Dolby Digital decoder or an amplifier with a built-in Dolby Digital decoder.

STREAM/PCM: Select this when you connect the digital input connector of an amplifier with a built-in DTS, Dolby Digital, or MPEG multichannel decoder.

PCM ONLY: Select this when you connect the linear PCM digital input of other audio equipment (amplifier, MD or DAT deck, etc.).

8ANALOG AUDIO OUT — STEREO / DOLBY SURROUND

Various modes of this unit are categorized into menus nested in 2 levels shown in the following table. To change the settings of these modes, find the desired mode in the menu (for details on each menu, see pages 80 through 81), then follow the procedure below.

Select the appropriate setting to accommodate the unit to the connected A/V equipment. This function takes effect when a DVD VIDEO disc is played back.

STEREO: Select this when listening to conventional two-channel stereo audio with the unit’s AUDIO OUTPUT connectors connected to a stereo amplifier/receiver or TV set, or in case you want to record the audio from a DVD VIDEO disc to a Mini Disc, etc.

DOLBY SURROUND: Select this when listening to multichannel surround audio with the unit’s AUDIO OUTPUT connectors connected to an amplifier/receiver with a built-in surround decoder or a surround decoder.

DVD SET UP	LANGUAGE SET ( pg. 22)
	AUDIO OUTPUT ( pg. 80)
	UTILITY ( pg. 41, 87)
FUNCTION SET UP	VIDEO IN/OUT ( pg. 25, 74)
	RECORDING SET ( pg. 81)
	DISPLAY SET ( pg. 81)
	OTHERS ( pg. 81)
INITIAL SET UP	AUTO CH SET ( pg. 83)
	MANUAL CH SET ( pg. 84)
	SAT/GUIDE PR ( pg. 23, 83)
	CLOCK SET ( pg. 86)

●The procedure below shows how to set the desired option of the “AUDIO REC” mode as an example.

1 Press VCR/DVD repeatedly so that the DVD lamp lights up on the unit.

2 Press SET UP to access the Main Menu screen.

3

4 Press w e to select “RECORDING SET”, then press

ENTER.

5 Press rt to select “AUDIO REC”, then press ENTER.

6 Press rt to select the desired option, then press ENTER.

7 Press SET UP to complete the setting.

8D. RANGE CONTROL — NORMAL / WIDE RANGE / TV

MODE

The dynamic range (the difference between the loudest sound and the quietest one) can be compressed during playback of a programme encoded in Dolby Digital format.

This function takes effect when a DVD VIDEO disc recorded in Dolby Digital format is played back at low or middle volume. NORMAL: Normally select this setting to activate this function. WIDE RANGE: Select this to deactivate this function when you

enjoy wide dynamic range programme.

TV MODE: Select this when you hear the sound through the TV’s speaker(s).

NOTES:

●This function takes no effect on programmes other than that recorded in Dolby Digital format.

●This function dose not work when Simulated Surround Effect is activated. ( pg. 38)

●The effect of “NORMAL” and “WIDE RANGE” may not be different depending on discs.

8OUTPUT LEVEL — STANDARD / LOW

You can lower the output level of analog audio to accommodate the unit to the connected A/V equipment.

STANDARD: Normally select this setting.

LOW: The output level of analog audio is lowered.

Page 80

April 15, 2004 3:21 pm