Overview
If you have inserted Insert Effects, the Send 1 and 2 parameters of P7 in Program Edit mode will become effective (those of P5 will be ignored). If you have not inserted Insert Effects, the Send 1 and 2 parameters of P5 in Global mode and P5 in Program Edit mode will become effective.
The Send 1 and 2 parameters are also used to set the level of signal appearing at output connectors 3 and 4.
Only the Master Effect sound will be sent to output connectors 3 and 4. If you wish to output dry sound (without the Master Effects applied), set the Master Effect parameters of P8 in Program Edit mode to “Off.” In this case, however, the Master Effect will not be applied to the signal at outputs 1 and 2.
If output connectors 3 and 4 are used for stereo output, you can set the stereo position of Send 1 and 2 using the Pan 3 and 4 parameters (P8 in Program Edit mode).
To set the Master Effect return level, use the Return 1 and 2 parameters (P8 in Program Edit mode).
If you check the check box located between Send 1 and Send 2 in the upper left corner of the LCD, the serial routing of Modulation → Reverb/Delay will be added. That is, the Right modulation output will be added to the Reverb/Delay input. In this case, you can also set the Return 1 and 2 parameters indepen- dently.
Combination
Mixer | Insert Effect Grouping | Master Effects |
(Combination Edit P1) | (Combination Edit P7) | (Combination Edit P8) |
Timbre1 |
| in the case of |
|
|
|
|
|
|
|
| Master Effects | Pan1 |
| |
|
|
| Insert Effect =Off |
|
|
|
|
|
|
|
|
| ||
|
|
| Send1 |
| + |
| Insert Effect=Off |
| + | Modulation |
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
| + |
|
| + | Reverb/Delay |
|
| |||
|
|
| Send2 |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| Pan2 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
OSC1 | Filter1 | Amp1 |
|
|
|
|
|
|
| Send1 | + |
|
|
|
Pan |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| Send2 | + |
|
|
| |
|
|
|
|
|
|
|
|
|
| Return2 | Return1 |
| ||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| Send1 |
|
|
|
|
|
| + + |
|
|
|
|
|
|
|
|
|
|
| Insert Effects |
|
| LEQ | HEQ | |||
|
|
|
|
| + |
|
| + | + | |||||
|
|
| Send2 |
|
|
|
|
|
| + |
| |||
OSC2 | Filter2 | Amp2 |
| + | + |
| E1 | E2 | E3 |
| + | + | + |
|
Pan |
| InsertEffects |
|
|
|
| ||||||||
Timbre2 |
| + |
| Grouping/ |
|
|
|
|
|
|
| |||
| in the case of |
|
|
|
| Pan Width |
|
|
| |||||
|
|
| in the case of |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Insert Effect =On |
|
|
|
|
|
|
|
|
| Low Gain High Gain | |
|
|
| Insert Effect =Off |
| + | Assigning | Timbreto |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| Send1 |
| + |
|
|
|
|
|
|
|
|
|
|
|
| Send2 |
|
|
|
|
|
|
|
|
|
|
|
OSC1 | Filter1 | Amp1 |
| + |
|
|
|
|
| Send1 |
|
|
|
|
Pan |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| + |
|
|
|
|
| Send2 |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| Send1 |
|
|
|
|
|
| + + |
|
|
|
|
|
|
|
|
|
|
| Insert Effects |
|
|
|
| |||
|
|
| Send2 |
| + |
|
| + |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| + |
| E1 | E2 | E3 |
|
|
|
| ||
OSC2 | Filter2 | Amp2 |
| + |
|
| + |
|
|
| ||||
Pan |
|
|
|
|
|
|
|
| ||||||
|
|
| + |
|
|
|
|
|
|
|
|
|
| |
|
|
| in the case of |
|
|
|
|
|
| Pan Width |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Insert Effect =On |
|
|
|
|
|
|
|
|
|
|
|
OUT3
OUT4
OUT1 |
OUT2 |
up to
Timbre8
Insert Effect=Off
Combination
Insert Effects
The Insert Effects selected in Program Edit mode are not used in Combination Edit mode. Instead, you can set Insert Effects for up to eight Timbres in a Combination.
Go to P7 in Combination Edit mode, and set the Insert Effect’s Off, size (1, 2, 4, 8), and grouping parame- ters for each of Timbres
If you wish to use a Program’s Insert Effect settings by using the Copy function, first select a size for the corresponding Timbre equal to or greater than the size of the effects used in the Program.
You can route up to three Insert Effects for each Timbre in series. (If the Program is using a DrumKit, you can use up to four effects in series or parallel.)
The total effect size for all the Timbres must be eight or less.
6
