04:
04: Overdrive/Hi-Gain
This distortion effect utilizes an Overdrive mode and a
Mono In - Mono Out |
|
In | Wet / Dry |
| |
Pre | 4 Band PEQ |
Driver |
|
| Output Level |
Mode: Overdrive / |
|
Drive | Direct Mix |
a | Mode | Overdrive, | Switches between overdrive and | |||
|
|
|
|
|
| |
b | Drive | 0… | 100 |
| Sets the degree of distortion. ☞ P.19 | |
|
|
|
|
|
| |
c | Output Level | 0… | 50 |
| Sets the output level.☞ P.19 | |
|
|
|
|
|
|
|
d | Pre | 0… | 10 |
| Amount of cut in low range at the distortion input. | |
| ☞ P.19 | |||||
|
|
|
|
|
| |
|
|
|
|
|
| |
| Band1 Cutoff [Hz] | 20… |
| 1.0kHz | Center frequency of EQ band 1 | |
|
|
|
|
| ||
e | Q | 0.5… | 10.0 | Band 1 bandwidth ☞ P.19 | ||
|
|
|
|
| ||
| Gain [dB] | +18dB | Band 1 gain | |||
|
|
|
|
|
| |
| Band2 Cutoff [Hz] | 50… |
| 5.00kHz | Band 2 center frequency | |
|
|
|
|
| ||
f | Q | 0.5… | 10.0 | Band 2 bandwidth ☞ P.19 | ||
|
|
|
|
| ||
| Gain [dB] | +18dB | Band 2 gain | |||
|
|
|
|
| ||
| Band3 Cutoff [Hz] | 300… | 10.00kHz | Band 3 center frequency | ||
|
|
|
|
| ||
g | Q | 0.5… | 10.0 | Band 3 bandwidth ☞ P.19 | ||
|
|
|
|
| ||
| Gain [dB] | +18dB | Band 3 gain | |||
|
|
|
|
| ||
| Band4 Cutoff [Hz] | 500… | 20.00kHz | Band 4 center frequency | ||
|
|
|
|
| ||
h | Q | 0.5… | 10.0 | Band 4 bandwidth ☞ P.19 | ||
|
|
|
|
| ||
| Gain [dB] | +18dB | Band 4 gain | |||
|
|
|
|
|
| |
i | Direct Mix | 0… | 50 |
| Mix amount of dry sound routed to Distortion | |
|
|
|
| |||
| Wet/Dry | Dry, 1:99… 99:1, Wet | Sets the balance between the effect and dry sounds. | |||
|
|
|
|
| ||
j | Src | None… | Tempo | Modulation source of effect balance | ||
|
|
|
|
| ||
| Amt | +100 | Modulation amount of effect balance | |||
|
|
|
|
|
|
|
b: Drive | The degree of distortion is determined by the level of input signal and the set- |
c: Output Level | ting of Drive. Raising the Drive setting will cause the entire volume level to |
| increase. Use the Output Level parameter to adjust the volume level. The Out- |
| put Level parameter uses the signal level input to the |
| occurs at the |
size1 |
d: Pre | Cutting the signal in the low range before it is input to the Distortion will create |
| a sharp distortion. |
e: Q | These parameters set the bandwidth of each band filter. The higher the value, |
f: Q | the narrower the band becomes. |
g: Q |
|
h: Q |
|
19
