Exit Configuration Mode, Expert Settings

Configuration Via Serial Mode or Telnet Port

Expert Settings

TCP keepalive	45 (seconds)

ARP cache timeout	600 (seconds)

Security Settings

Disable SNMP	(N) No

SNMP Community Name	public

Disable Telnet Setup	(N) No

Disable TFTP Firmware Update	(N) No

Disable Port 77FEh	(N) No

Disable Web Server	(N) No

Disable ECHO ports	(Y) Yes

Enable Enhanced password	(N) No

Disable Port 77F0h	(N) No

Email Settings

Trigger Priority	L

Min. notification interval	1 second

All other parameters	0 (e.g. Email notification and triggers are disabled)

Exit Configuration Mode

To exit setup mode:

Select option 9 Save and exit from the Change Setup menu to save all changes and reboot the device. All values are stored in nonvolatile memory. or

Select option 8 Exit without save from the Change Setup menu to exit the configuration mode without saving any changes or rebooting,

5-24	WiPort™ User Guide

Page 66

Image 66

Lantronix 900-332 manual Exit Configuration Mode, Expert Settings, Security Settings, Email Settings

Contents

WiPort User Guide Page Lantronix Corporate Headquarters Technical SupportSales Offices Disclaimer and Revisions Contents Wlan Settings5-19 ContentsAccessing Setup Mode Expert Settings5-20 Gpio Pins Factory DefaultsExit Configuration Mode Control ProtocolPage Chapter Summary Using This GuidePurpose and Audience Remaining chapters in this guide include Using This Guide Additional Documentation Introduction Capabilities Protocol Support Configuration MethodsApplications Introduction IP Address Addresses and Port NumbersHardware Address Port NumbersPage Configuration using DeviceInstaller Accessing WiPort using DeviceInstallerServer Configuration Wlan Configuration Host List Configuration OEM Pin ConfigurationConfiguration Using DeviceInstaller Channel 1 and Channel 2 Configuration UDP Datagram Mode Common I/F Mode SettingSerial Settings Passive Connection Active Connection Disconnection ConnectionBuffer Flushing Email Configuration Packing Triggers Unit NamePage Configuration using Web-Manager Accessing WiPort using Web-Manager Network Configuration Configuration Using Web-Manager Click the OK button when finished Automatic IP Address ConfigurationStatic IP Address Configuration Select Obtain IP address automatically IP Address Select Use the following IP configurationDefault Gateway Subnet Mask Server Configuration Advanced Serial Settings Retry SettingsHost Information Available fields, enter the following information Port SettingsDisable Serial Port Channel Flush Input Buffer Serial to Network Connection Settings TCPPack Control Flush Output Buffer Network to Serial Connect Mode Passive Connection Connect Mode Active ConnectionConnect Protocol Endpoint Configuration Disconnect ModeCommon Options Connection Settings UDP Datagram Mode Configure the following fields Change Address TableMail Server IP Address Recipients Configurable PinsEnable Serial Trigger Conditions Message Properties Ad Hoc Settings Wireless Network SecurityEnter or modify the following fields Advanced Settings Configure or modify the following fields for each pin Updating Settings Page Configuration via Serial Mode or Telnet Port Accessing Setup ModeTelnet Access Serial Port Access Configuration Via Serial Mode or Telnet PortClick OK. The following information displays Set the IP Address Set the Gateway IP Address Dhcp Name Change Telnet Configuration PasswordSet the Netmask Network Class Host Bits Netmask Mode Option Interface ModeFollowing table displays available I/F Mode options Interface Mode Options Port Number Common I/F Mode Setting Binary HexFlow Flow Control Option Connect Mode Option Connect ModeEnter Connect Mode options in hexadecimal notation Port Numbers Reserved for Incoming Connection Response Manual Connection Manual Connection Address ExampleAutostart Automatic Connection Hostlist Hostlist Example Modem Mode Datagram TypeMessage Meaning Modem Mode Command Modem Mode CommandsFunction Modem Mode Function Command Remote IP AddressRemote Port 10. Disconnect Mode Options Flush ModeDisconnect Mode Option 11. Flush Mode Options Option SendChar 1 and SendChar2 DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal Type Mail Server Recipient Unit NameDomain Name Trigger Enable Ad Hoc Network Creation Wlan SettingsEnable Wlan Find Network Name Expert Settings Security Settings Disable Tftp Firmware Upgrade Disable SnmpDisable Telnet Setup Disable Port 77FE Hex Factory Defaults Channel 1 Configuration Channel 2 ConfigurationWlan Settings Security Settings Exit Configuration ModeExpert Settings Email Settings Features Configurable PinsGpio Pins Control Protocol Byte 0 Command Types CommandsConfigurable Pins Command 10h, Get Functions Command 13h, Get Current States Command 11h, Get DirectionsCommand 12h, Get Active Levels Command 19h, Set Directions Command details Command 1Ah, Set Active LevelsCommand 1Bh, Set States Examples 1Bh = response to command 1Bh 03h, 00h, 00h, 00h = Page Entering Monitor Mode via the Network Port Monitor ModeEntering Monitor Mode via the Serial Port To enter Monitor Mode locally Command Command Name Function Monitor Mode CommandsFollowing commands are available in Monitor Mode Monitoring the Network Obtaining Firmware Reloading Firmware Using Tftp Graphical User InterfaceUpdating Firmware ROM File FWX File Using Tftp Command Line Interface Recovering the Firmware Using the Serial PortTroubleshooting Troubleshooting Problems and Error MessagesProblem/Message Reason Solution Please try again Caps Lock is not on General DeviceInstaller Settings Device Server message Technical Support Technical Support Europe, Middle East, and Africa

Lantronix 900-332 Exit Configuration Mode, Expert Settings, Security Settings, Email Settings

Models: 900-332

Configuration Via Serial Mode or Telnet Port

Expert Settings

TCP keepalive

45 (seconds)

ARP cache timeout

Security Settings

Email Settings

Exit Configuration Mode