Channel 1 Configuration, Wlan Settings | Lantronix 900-332 manual

		Configuration Via Serial Mode or Telnet Port
	Channel 1 Configuration
	Baudrate	9600

	I/F Mode	4C (1 stop bit, no parity, 8 bit, RS-232C)

	Port No	10001

	Connect Mode	C0 (always accept incoming connection; no active
		connection startup)

	Hostlist Retry Counter	3

	Hostlist Retry Timeout	250 (msec)

	Send Character	0x0D (CR)

	All other parameters	0

	Channel 2 Configuration

	Baudrate	9600

	I/F Mode	4C (1 stop bit, no parity, 8 bit, RS-232C)

	Port No	10002

	Connect Mode	C0 (always accept incoming connection; no active
		connection startup)

	Hostlist Retry Counter	3

	Hostlist Retry Timeout	250 (msec)

	Send Character	0x0D (CR)

	All other parameters	0

	WLAN Settings

	Enable WLAN	(Y) Yes

	Find Network Name	LTRX_IBSS

	Enable Ad Hoc Network Creation	(Y) Yes

	Name	LTRX_IBSS

	Country	(0) United States

	Channel	11

	Security	(0) None

	Data Rate	11Mbps

WiPort™ User Guide

5-23

Page 65

Image 65

Lantronix 900-332 manual Channel 1 Configuration, Channel 2 Configuration, Wlan Settings

Contents

WiPort User Guide Page Sales Offices Lantronix Corporate HeadquartersTechnical Support Disclaimer and Revisions Contents Accessing Setup Mode ContentsWlan Settings5-19 Expert Settings5-20 Exit Configuration Mode Factory DefaultsGpio Pins Control ProtocolPage Purpose and Audience Using This GuideChapter Summary Remaining chapters in this guide include Additional Documentation Using This Guide Capabilities Introduction Applications Configuration MethodsProtocol Support Introduction Hardware Address Addresses and Port NumbersIP Address Port NumbersPage Server Configuration Configuration using DeviceInstallerAccessing WiPort using DeviceInstaller Wlan Configuration Configuration Using DeviceInstaller Host List ConfigurationOEM Pin Configuration Channel 1 and Channel 2 Configuration Serial Settings Common I/F Mode SettingUDP Datagram Mode Passive Connection Active Connection Buffer Flushing DisconnectionConnection Packing Email Configuration Unit Name TriggersPage Accessing WiPort using Web-Manager Configuration using Web-Manager Configuration Using Web-Manager Network Configuration Static IP Address Configuration Automatic IP Address ConfigurationClick the OK button when finished Select Obtain IP address automatically Default Gateway Select Use the following IP configurationIP Address Subnet Mask Advanced Server Configuration Host Information Serial SettingsRetry Settings Disable Serial Port Port SettingsAvailable fields, enter the following information Channel Pack Control Connection Settings TCPFlush Input Buffer Serial to Network Flush Output Buffer Network to Serial Connect Protocol Connect Mode Passive ConnectionConnect Mode Active Connection Common Options Endpoint ConfigurationDisconnect Mode Datagram Mode Connection Settings UDP Mail Server IP Address Configure the following fieldsChange Address Table Enable Serial Trigger Configurable PinsRecipients Conditions Message Properties Enter or modify the following fields Ad Hoc SettingsWireless Network Security Configure or modify the following fields for each pin Advanced Settings Updating Settings Page Telnet Access Configuration via Serial Mode or Telnet PortAccessing Setup Mode Click OK. The following information displays Serial Port AccessConfiguration Via Serial Mode or Telnet Port Set the Gateway IP Address Set the IP Address Set the Netmask Change Telnet Configuration PasswordDhcp Name Network Class Host Bits Netmask Following table displays available I/F Mode options Interface ModeMode Option Interface Mode Options Flow Common I/F Mode Setting Binary HexPort Number Flow Control Option Enter Connect Mode options in hexadecimal notation Connect ModeConnect Mode Option Port Numbers Reserved for Response Incoming Connection Autostart Automatic Connection Manual ConnectionManual Connection Address Example Hostlist Example Hostlist Message Meaning Modem ModeDatagram Type Function Modem Mode CommandModem Mode Commands Remote Port Modem Mode Function CommandRemote IP Address Disconnect Mode Option Flush Mode10. Disconnect Mode Options 11. Flush Mode Options Option Channel Port Password DisConnTime Inactivity TimeoutSendChar 1 and SendChar2 Telnet Terminal Type Mail Server Domain Name Unit NameRecipient Trigger Enable Wlan Wlan SettingsEnable Ad Hoc Network Creation Find Network Name Security Settings Expert Settings Disable Telnet Setup Disable SnmpDisable Tftp Firmware Upgrade Disable Port 77FE Hex Factory Defaults Wlan Settings Channel 1 ConfigurationChannel 2 Configuration Expert Settings Exit Configuration ModeSecurity Settings Email Settings Gpio Pins Configurable PinsFeatures Control Protocol Configurable Pins CommandsByte 0 Command Types Command 10h, Get Functions Command 12h, Get Active Levels Command 11h, Get DirectionsCommand 13h, Get Current States Command 19h, Set Directions Command 1Bh, Set States Command 1Ah, Set Active LevelsCommand details Examples 1Bh = response to command 1Bh 03h, 00h, 00h, 00h = Page Entering Monitor Mode via the Serial Port Monitor ModeEntering Monitor Mode via the Network Port To enter Monitor Mode locally Following commands are available in Monitor Mode Monitor Mode CommandsCommand Command Name Function Monitoring the Network Updating Firmware Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM File FWX File Troubleshooting Using Tftp Command Line InterfaceRecovering the Firmware Using the Serial Port Problem/Message Reason Solution TroubleshootingProblems and Error Messages Caps Lock is not on Please try again Device Server message General DeviceInstaller Settings Technical Support Europe, Middle East, and Africa Technical Support

Channel 1 Configuration

Channel 2 Configuration

WLAN Settings

Security