WiPort User Guide | Lantronix 900-332 instruction

WiPort™ User Guide

Part Number 900-332 Revision A 3/04

Image 1

Lantronix 900-332 manual WiPort User Guide

Contents

WiPort User Guide Page Technical Support Lantronix Corporate HeadquartersSales Offices Disclaimer and Revisions Contents Accessing Setup Mode ContentsWlan Settings5-19 Expert Settings5-20 Exit Configuration Mode Factory DefaultsGpio Pins Control ProtocolPage Purpose and Audience Using This GuideChapter Summary Remaining chapters in this guide include Additional Documentation Using This Guide Capabilities Introduction Applications Configuration MethodsProtocol Support Introduction Hardware Address Addresses and Port NumbersIP Address Port NumbersPage Accessing WiPort using DeviceInstaller Configuration using DeviceInstallerServer Configuration Wlan Configuration OEM Pin Configuration Host List ConfigurationConfiguration Using DeviceInstaller Channel 1 and Channel 2 Configuration Serial Settings Common I/F Mode SettingUDP Datagram Mode Passive Connection Active Connection Connection DisconnectionBuffer Flushing Packing Email Configuration Unit Name TriggersPage Accessing WiPort using Web-Manager Configuration using Web-Manager Configuration Using Web-Manager Network Configuration Static IP Address Configuration Automatic IP Address ConfigurationClick the OK button when finished Select Obtain IP address automatically Default Gateway Select Use the following IP configurationIP Address Subnet Mask Advanced Server Configuration Retry Settings Serial SettingsHost Information Disable Serial Port Port SettingsAvailable fields, enter the following information Channel Pack Control Connection Settings TCPFlush Input Buffer Serial to Network Flush Output Buffer Network to Serial Connect Mode Active Connection Connect Mode Passive ConnectionConnect Protocol Disconnect Mode Endpoint ConfigurationCommon Options Datagram Mode Connection Settings UDP Change Address Table Configure the following fieldsMail Server IP Address Enable Serial Trigger Configurable PinsRecipients Conditions Message Properties Wireless Network Security Ad Hoc SettingsEnter or modify the following fields Configure or modify the following fields for each pin Advanced Settings Updating Settings Page Accessing Setup Mode Configuration via Serial Mode or Telnet PortTelnet Access Configuration Via Serial Mode or Telnet Port Serial Port AccessClick OK. The following information displays Set the Gateway IP Address Set the IP Address Set the Netmask Change Telnet Configuration PasswordDhcp Name Network Class Host Bits Netmask Following table displays available I/F Mode options Interface ModeMode Option Interface Mode Options Flow Common I/F Mode Setting Binary HexPort Number Flow Control Option Enter Connect Mode options in hexadecimal notation Connect ModeConnect Mode Option Port Numbers Reserved for Response Incoming Connection Manual Connection Address Example Manual ConnectionAutostart Automatic Connection Hostlist Example Hostlist Datagram Type Modem ModeMessage Meaning Modem Mode Commands Modem Mode CommandFunction Remote IP Address Modem Mode Function CommandRemote Port Disconnect Mode Option Flush Mode10. Disconnect Mode Options 11. Flush Mode Options Option Channel Port Password DisConnTime Inactivity TimeoutSendChar 1 and SendChar2 Telnet Terminal Type Mail Server Domain Name Unit NameRecipient Trigger Enable Wlan Wlan SettingsEnable Ad Hoc Network Creation Find Network Name Security Settings Expert Settings Disable Telnet Setup Disable SnmpDisable Tftp Firmware Upgrade Disable Port 77FE Hex Factory Defaults Channel 2 Configuration Channel 1 ConfigurationWlan Settings Expert Settings Exit Configuration ModeSecurity Settings Email Settings Gpio Pins Configurable PinsFeatures Control Protocol Configurable Pins CommandsByte 0 Command Types Command 10h, Get Functions Command 12h, Get Active Levels Command 11h, Get DirectionsCommand 13h, Get Current States Command 19h, Set Directions Command 1Bh, Set States Command 1Ah, Set Active LevelsCommand details Examples 1Bh = response to command 1Bh 03h, 00h, 00h, 00h = Page Entering Monitor Mode via the Serial Port Monitor ModeEntering Monitor Mode via the Network Port To enter Monitor Mode locally Following commands are available in Monitor Mode Monitor Mode CommandsCommand Command Name Function Monitoring the Network Updating Firmware Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM File FWX File Recovering the Firmware Using the Serial Port Using Tftp Command Line InterfaceTroubleshooting Problems and Error Messages TroubleshootingProblem/Message Reason Solution Caps Lock is not on Please try again Device Server message General DeviceInstaller Settings Technical Support Europe, Middle East, and Africa Technical Support