Factory Defaults | Lantronix 900-332 guide

Configuration Via Serial Mode or Telnet Port

Disable Port 77FEh (N) ? _

The default setting is the N (No) option, which enables remote configuration. As a result, configure the unit by using DeviceInstaller, web pages, Telnet, or serial configuration.

The Y (Yes) option disables remote configuration and web sites.

Note: The Y (Yes) option disables many of the GUI tools for configuring the unit, including the embedded Web-Manager tool.

Disable Web Server

The Y (Yes) option disables the web server. This setting defaults to the N (option).

Disable Web Server (N) ? _

Disable Web Setup

The Y (Yes) option disables configuration via the Web-Manager. This setting defaults to the N (option).

Disable Web Setup (N) ? _

Disable ECHO Ports

This setting controls whether the serial port echoes characters it receives. The current value is displayed in parentheses.

Disable ECHO ports (Y) ? _

Enable Enhanced Password

This setting defaults to the N (option), which permits a 4-character password protecting Setup Mode by means of Telnet and web pages.

Enable Enhanced Password (Y) ? _

The Y (Yes) option allows an extended security password of 16-characters for protecting Telnet access.

Disable Port 77F0 (Hex)

Port 77F0 is a setting that allows a custom application to query or set the eleven WiPort configurable pins when they are functioning as general purpose I/O (GPIO). Disable this capability, if desired, for security purposes.

Disable Port 77F0h ? _

The default setting, the N (No) option, enables GPIO control. The Y (Yes) option disables the GPIO control interface.

Factory Defaults

Select 7 Factory Defaults from the Change Setup menu to reset the unit’s Channel 1 configuration, Channel 2 configuration, E-mail settings, and Expert settings to the factory default settings. The server configuration settings for IP address, gateway IP address, and netmask remain unchanged. The configurable pins’ settings also remain unchanged. The specific settings that this option changes are listed below:

5-22	WiPort™ User Guide

Image 64

Lantronix 900-332 manual Factory Defaults

Contents

WiPort User Guide Page Technical Support Lantronix Corporate HeadquartersSales Offices Disclaimer and Revisions Contents Contents Accessing Setup ModeWlan Settings5-19 Expert Settings5-20 Factory Defaults Exit Configuration ModeGpio Pins Control ProtocolPage Using This Guide Purpose and AudienceChapter Summary Remaining chapters in this guide include Using This Guide Additional Documentation Introduction Capabilities Configuration Methods ApplicationsProtocol Support Introduction Addresses and Port Numbers Hardware AddressIP Address Port NumbersPage Accessing WiPort using DeviceInstaller Configuration using DeviceInstallerServer Configuration Wlan Configuration OEM Pin Configuration Host List ConfigurationConfiguration Using DeviceInstaller Channel 1 and Channel 2 Configuration Common I/F Mode Setting Serial SettingsUDP Datagram Mode Passive Connection Active Connection Connection DisconnectionBuffer Flushing Email Configuration Packing Triggers Unit NamePage Configuration using Web-Manager Accessing WiPort using Web-Manager Network Configuration Configuration Using Web-Manager Automatic IP Address Configuration Static IP Address ConfigurationClick the OK button when finished Select Obtain IP address automatically Select Use the following IP configuration Default GatewayIP Address Subnet Mask Server Configuration Advanced Retry Settings Serial SettingsHost Information Port Settings Disable Serial PortAvailable fields, enter the following information Channel Connection Settings TCP Pack ControlFlush Input Buffer Serial to Network Flush Output Buffer Network to Serial Connect Mode Active Connection Connect Mode Passive ConnectionConnect Protocol Disconnect Mode Endpoint ConfigurationCommon Options Connection Settings UDP Datagram Mode Change Address Table Configure the following fieldsMail Server IP Address Configurable Pins Enable Serial TriggerRecipients Conditions Message Properties Wireless Network Security Ad Hoc SettingsEnter or modify the following fields Advanced Settings Configure or modify the following fields for each pin Updating Settings Page Accessing Setup Mode Configuration via Serial Mode or Telnet PortTelnet Access Configuration Via Serial Mode or Telnet Port Serial Port AccessClick OK. The following information displays Set the IP Address Set the Gateway IP Address Change Telnet Configuration Password Set the NetmaskDhcp Name Network Class Host Bits Netmask Interface Mode Following table displays available I/F Mode optionsMode Option Interface Mode Options Common I/F Mode Setting Binary Hex FlowPort Number Flow Control Option Connect Mode Enter Connect Mode options in hexadecimal notationConnect Mode Option Port Numbers Reserved for Incoming Connection Response Manual Connection Address Example Manual ConnectionAutostart Automatic Connection Hostlist Hostlist Example Datagram Type Modem ModeMessage Meaning Modem Mode Commands Modem Mode CommandFunction Remote IP Address Modem Mode Function CommandRemote Port Flush Mode Disconnect Mode Option10. Disconnect Mode Options 11. Flush Mode Options Option DisConnTime Inactivity Timeout Channel Port PasswordSendChar 1 and SendChar2 Telnet Terminal Type Mail Server Unit Name Domain NameRecipient Trigger Wlan Settings Enable WlanEnable Ad Hoc Network Creation Find Network Name Expert Settings Security Settings Disable Snmp Disable Telnet SetupDisable Tftp Firmware Upgrade Disable Port 77FE Hex Factory Defaults Channel 2 Configuration Channel 1 ConfigurationWlan Settings Exit Configuration Mode Expert SettingsSecurity Settings Email Settings Configurable Pins Gpio PinsFeatures Control Protocol Commands Configurable PinsByte 0 Command Types Command 10h, Get Functions Command 11h, Get Directions Command 12h, Get Active LevelsCommand 13h, Get Current States Command 19h, Set Directions Command 1Ah, Set Active Levels Command 1Bh, Set StatesCommand details Examples 1Bh = response to command 1Bh 03h, 00h, 00h, 00h = Page Monitor Mode Entering Monitor Mode via the Serial PortEntering Monitor Mode via the Network Port To enter Monitor Mode locally Monitor Mode Commands Following commands are available in Monitor ModeCommand Command Name Function Monitoring the Network Using Tftp Graphical User Interface Updating FirmwareObtaining Firmware Reloading Firmware ROM File FWX File Recovering the Firmware Using the Serial Port Using Tftp Command Line InterfaceTroubleshooting Problems and Error Messages TroubleshootingProblem/Message Reason Solution Please try again Caps Lock is not on General DeviceInstaller Settings Device Server message Technical Support Technical Support Europe, Middle East, and Africa