Manuals
/
Brands
/
Household Appliance
/
Home Security System
/
Linear
/
Household Appliance
/
Home Security System
Linear
DVS-2400 manual
1
1
44
44
Download
44 pages, 2.58 Mb
SECURITY
SUPERVISED WIRELESS
SECURITY CONSOLE
Installation & Programming Instructions
(760)
438-7000
• FAX (760)
438-7043
www.linearcorp.com
Contents
Installation & Programming Instructions
INTRODUCTION
TABLE OF CONTENTS
1. THE DVS-2400SECURITY SYSTEM
not
both
simultaneously
are
2. SECURITY SYSTEM FLOOR PLAN
3. TYPICAL SYSTEM SENSORS
4. CONSOLE FEATURES
Page
5. CONSOLE INSTALLATION
EXTERNAL CONSOLE SPEAKER CONNECTION (OPTIONAL)
With the
Use an
◆Up to two 8-ohmspeakers can be used with each Console
◆Up to 150 feet of 22 AWG wire can be used with each speaker
TELEPHONE LINE CONNECTION (OPTIONAL)
Connect the Console to the telephone line if the system is monitored, requires
Install a USOC RJ31-Xor RJ38-Xjack to the telephone system near the Console
Route an appropriate modular telephone line cord from the jack to the Console
Route the line cord through the Console’s wiring access hole
(do not plug the transformer in until the wiring is complete)
unswitched
6. BASIC CONSOLE PROGRAMMING
PROGRAMMING DIFFERENT SENSOR TYPES
press and hold the keypad’s
] key until programmed into the Console
IMPORTANT NOTE: The
NOTE: After the Console “learns” the transmitter
7.BASIC SENSOR INSTALLATION
DXS-31& DXS-32DOOR/WINDOW SENSORS
External normally closed switches
The door/window sensor
SET SENSOR JUMPER
◆A jumper inside the door/window sensor selects instant or delayed response
8.CUSTOMIZING THE CONSOLE
9. CONSOLE OPERATING MODES
OFF MODE
CHIME MODE
START HERE
(OPTIONAL)
OR CHIME MODE
START IN
HOME MODE
1 GONG
& 2 BEEPS
AWAY MODE
& 3 BEEPS
QUICK ARM
& 3 BEEPS DONE
TEST MODE
& 4 BEEPS
10.SYSTEM TROUBLE INDICATIONS
11.CUSTOMIZING THE SYSTEM
will not
SENSOR NUMBER FOR CHIME
8 FOR
8 TUV CHIME FUNCTION
AWAY 1 BING
START IN TEST
MASTER
1 GONG &
5 BEEPS
SENSOR
12. ADVANCED PROGRAMMING
CHANGING A SENSORS SUPERVISION
◆Any sensor can be programmed as supervised or non-supervised
CHANGING A SENSORS RESTORE REQUIREMENTS
◆Any sensor can be programmed as manual or automatic restore
ENTRY DELAY TIME
Page
SILENT BURGLARY ALARMS
◆The factory setting causes audible burglary alarms
◆Alternately, the Console can be programmed for silent burglary alarms
SILENT EMERGENCY ALARMS
◆The factory setting causes audible emergency alarms
AUTOMATION OUTPUT MODE DURING ALARM
AUTOMATION ACTIVATION TONE
◆Alternately, this sound can be silenced
REMOTE CONTROL ARM/DISARM CHIRP
◆Alternately, these chirps can be silenced
two or more digits different than any user code
ADDITIONAL USER CODES
ARM OR DISARM
Log the restricted user codes in the boxes
REMOVING USER CODES
Any restricted, duress or page alert user code can be removed from the Console
13. COMMUNICATOR PROGRAMMING
SETUP MODE
GENERAL COMMUNICATOR OPTIONS
COMMUNICATOR ENABLE
2-WAYAUDIO
When the Model
The audio module can be programmed for listen only
CALL LIMITER
DIALING DELAY
DIALING METHOD
The factory setting causes the communicator to dial using DTMF
COMMUNICATOR REPORTING OPTIONS
REPORTING FORMAT
CALL ROUTING
Communicator Reporting Option Table
ACCOUNT NUMBER
◆The communicator’s account number entered must be 4-digitslong
◆The factory setting for the account number is
◆Enter an account number from 0000 to
PRIMARY TELEPHONE NUMBER
REPORT CONSOLE TROUBLE
REPORT FORCE ARMING
◆The factory setting does not send force arming reports
The factory set reporting code for force arming is “65” (Code 574 with Ademco)
OPENING AND CLOSING REPORTS
COMMUNICATOR REPORTING CODES
◆If Point ID reporting is enabled (the factory
default setting), each sensor can report a unique
alarm and trouble code
◆ If Point ID is disabled, the “general” reporting
FORCE ARMING REPORTING CODE
◆Programming Step #258
◆Any value from 0-99can be programmed for this event (0 = no report)
DURESS REPORTING CODE
◆Programming Step #259
Page
Point ID Reporting Codes Table
IMPORTANT INFORMATION