Linear DVS-2400 The, TEST SENSORS, INSTANT/DELAY, SET SENSOR JUMPER, (WITH DXS-31SHOWN), Open door or window, OPTION JUMPERSELECTS, EXAMPLE INSTALLATIONS

DXS-31 & DXS-32 DOOR/WINDOW SENSORS

◆The DXS-31 and DXS-32 sensors can be used to monitor doors, windows, cabinets, crawl space doors, gates, freezer doors, and many other moving objects that could be used for intrusion or need to be monitored.

◆A built-in magnetic switch triggers the sensor when its magnet (mounted on the moving part or the door or window) moves away from the sensor.

◆External normally closed switches (DXS-31 only) can be wired to the sensor for remote triggering.

◆The door/window sensor (DXS-31 only) can connect directly to a glass break detector.

SET SENSOR JUMPER◆A jumper inside the door/window sensor selects instant or delayed response.

If the sensor is going to be used on the primary entry/exit door make sure that the jumper is in the DELAY position.

If the sensor is going to be used on a window or a door that is not going to be used to enter and exit the premises, set the jumper to the INSTANT position.

APPLY DOUBLE-STICK TAPE Apply double-stick tape (supplied) to back of sensors and magnets.◆Screws are also provided to mount sensors and magnets.◆Screws are preferred over the double-stick tape in permanent installations.ATTACH SENSORS AND MAGNETS On doors, mount sensor to door frame and magnet to door.

✍NOTE: Magnet must line up with mark on sensor case both horizontally & vertically.

Allow a maximum of 1/2" between magnet and sensor when door/window is closed. Snap sensor onto mounting plate. On windows, mount sensor to window frame and magnet to window.

Snap sensor onto mounting plate.

The magnet height is adjustable and an optional magnet spacer is provided for uneven surfaces.

TEST SENSORS

	EXAMPLE INSTALLATIONS
	(WITH DXS-31 SHOWN)
LEFT OPENING DOOR
	SLIDING WINDOW
TRANSMITTER
MOUNTED ON
DOOR JAMB	MAGNET MOUNTED
	ON WINDOW FRAME
(NOTE: SMALL END
OF TRANSMITTER UP)
MAGNET
MOUNTED
ON DOOR		TRANSMITTER
		MOUNTED ON
		WINDOW SILL
	RIGHT OPENING DOOR	DOUBLE-HUNG
		WINDOW
	TRANSMITTER	TRANSMITTER
		MOUNTED ON
	MOUNTED ON
		WINDOW FRAME
	DOOR JAMB
	(NOTE: SMALL END
	OF TRANSMITTER DOWN)	MAGNET
	MAGNET MOUNTED	MOUNTED
		ON WINDOW
	ON DOOR	SASH STILE

	INSTANT/DELAY	ANTENNA
	OPTION JUMPER
INPUT	MAGNET	TWO TYPE 2032
	ALIGNMENT
SELECT	MARK	BATTERIES
JUMPER
		BATTERY
		CLAMP
TRANSMIT		SCREW
INDICATOR
		BATTERY CLAMP
TEST		EXTERNAL
SWITCH
		INPUT
		TERMINALS

INSTANT/DELAYOPTION JUMPERSELECTS

INSTANT

SELECTS

DELAY

ATTACH MOUNTING PLATES

USING THE SCREWS OR

DOUBLE-STICK TAPE PROVIDED

NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK

TAPE IS NOT ALLOWED IN UL INSTALLATIONS

❇Console in Chime Mode should “ding-dong” when the sensor sends signal. Open door or window.❇Verify that light on the sensor glows momentarily when door/window is opened.

❇Status indicator on Console should remain lit for each door/window sensor that is left open.

OPEN DOOR, TRANSMIT INDICATOR SHOULD LIGHT

1.PLACE RECEIVER INTO PROGRAM OR "LEARN" MODE

2.ACTIVATE TRANSMITTER BY OPENING DOOR OR WINDOW

3.VERIFY THAT THE RECEIVER ACCEPTED THE SIGNAL

4.REPLACE TRANSMITTER COVER WHEN FINISHED

NOTE: THE TRANSMIT INDICATOR WILL ONLY LIGHT DURING TRANSMISSIONS WHEN THE CASE IS OPEN (EXCEPT WHEN PUSHING THE CASE FOR TESTING)

15