◆The Console can be programmed with five restricted user codes and one page alert user code.
◆The restricted user codes operate the system as usual, but cannot access Setup Mode.
◆The restricted user codes can access a special Code Mode that can be used to change or remove any of the five restricted user codes, the page alert user code, or the duress code.
◆The page alert user code dials the supervisory number (programmed for a pager) when it is used to ARM OR DISARM the system.
◆A restricted user code is a good one to give to children or any user that should be restricted from programming the Console.
✍NOTE: For maximum security, a
✍WARNING: NEVER PROGRAM ANY RESTRICTED OR PAGE ALERT USER CODE THE SAME AS THE MASTER USER CODE!
PROGRAMMING STEPS #93 TO 98
PROGRAM
STORE PROGRAM
STEP # 93 RESTRICTED USER CODE #1
STEP # 94 RESTRICTED USER CODE #2
STEP # 95 RESTRICTED USER CODE #3
STEP # 96 RESTRICTED USER CODE #4
STEP # 97 RESTRICTED USER CODE #5
STEP # 98 PAGE ALERT USER CODE
Log the restricted user codes in the boxes.◆Any restricted, duress or page alert user code can be removed from the Console.
◆Because access to programming would be impossible without a master user code, it cannot be removed using these steps.
9 WXY KEYPAD CODE 
PROGRAMMING STEPS #92 TO 98
TEST REMOVE
✍NOTE: The master user code can be removed using the Console master reset, although all other system programming with be reset to factory values and all sensors programmed will be erased.
| CONSOLE MASTER RESET | START IN TEST |
| ||
| ◆ Master resetting the Console will set all of the |
| |||
|
|
| ||
| programming options back to the factory values. |
|
|
| |
| The master user code will be reset to 1234. |
| MASTER |
| |
✍CAUTION: Master resetting the Console will erase |
| USER |
| |
| CODE |
| ||
the user codes and remove all programmed sensors. |
|
| ||
|
|
| ||
All Console and communicator programming values |
|
|
| |
will be reset to the factory defaults. |
| 1 GONG & |
| |
| Start with the system in Test Mode (Setup | TEST |
| ||
5 BEEPS |
| |||
|
|
| ||
| Mode cannot be reached from any other mode). |
|
|
| |
| From the Test Mode, enter the master user code | 9 WXY | STEP #999 |
| |
|
| |||
| then press [TEST]. |
|
| ||
9 WXY | FOR | USE THESE EXACT | ||
| ❇ A “Gong” and five “Beeps” will sound, signaling | MASTER | |||
| KEYSTROKES | |||
| that the system is in Setup Mode. |
| RESET | ||
| TO PERFORM A | |||
9 WXY |
| |||
| Enter programming Step #999. |
| MASTER RESET | ||
|
| |||
|
|
| ||
| Press [TEST]. | TEST | PRESS |
| |
| Enter the numbers 999 again. | TEST |
| ||
|
| |||
|
|
| ||
| Press [TEST] again. | 9 WXY |
|
| |
| ❇ A “Bing” will sound to indicate the beginning of |
| ENTER 999 |
| |
| the reset process. This process will take up to 10 | 9 WXY | TO OK THE |
| |
| seconds while the memory is being reset. |
| MASTER |
| |
| RESET |
| ||
| ◆ The system will revert to the first time | 9 WXY |
|
| |
|
|
| ||
| condition and the new master user code will be |
| PRESS TEST, |
| |
| 1234. Go to the “Basic Console Programming” | TEST | 1 BING SOUNDS, |
| |
WAIT ABOUT 10 |
| |||
| section of this manual to begin |
|
| ||
| SECONDS |
| ||
| the system. | DONE |
| ||
31