Manuals / Brands / Household Appliance / Home Security System / Linear / Household Appliance / Home Security System

Linear DVS-2400 CALL LIMITER, DIALING DELAY, DIALING METHOD, The factory setting causes the communicator to dial using DTMF

1 44

Download 44 pages, 2.58 Mb

CALL LIMITER

◆The factory setting for the call limiter is OFF. This allows the communicator to report burglary alarms, once for each sensor, as many times as they are triggered.

◆Optionally, the Console can be programmed to only allow five burglary reports total per arming period.

✍NOTE: Sensors programmed to 24-hour functions (Emergency, Panic, Fire) always send a Central Station Report and always sound the local siren regardless of the Call Limiter setting.

1

0PROGRAMMING STEP #101

1

HOME PROGRAM

0 FOR OFF (UNLIMITED)

1 FOR ON (5 VIOLATIONS)

AWAY STORE PROGRAM

DIALING DELAY

◆The factory setting will cause the communicator to dial the Central Station instantly when an alarm or supervisory event occurs.

◆Alternately, the communicator can be programmed to wait 30 seconds before dialing. This gives the user time to disarm the system and prevent communications in the case of a subscriber generated false alarm.

PROGRAMMING STEP #103

PROGRAM

0 FOR NO DELAY

1 FOR 30 SECOND DELAY

STORE PROGRAM

DIALING METHOD

◆The factory setting causes the communicator to dial using DTMF (dual-tone multi-frequency) tone dialing.

◆Alternately, the communicator can be programmed to use pulse (rotary) dialing. Use this option if the telephone line in the installation does not support tone dialing.

1

0PROGRAMMING STEP #104

4GHI

HOME PROGRAM

0 FOR TONE DIALING

1 FOR PULSE DAILING

AWAY STORE PROGRAM

34

Contents

Installation & Programming Instructions INTRODUCTION TABLE OF CONTENTS 1. THE DVS-2400SECURITY SYSTEM not both simultaneously are 2. SECURITY SYSTEM FLOOR PLAN 3. TYPICAL SYSTEM SENSORS 4. CONSOLE FEATURES Page 5. CONSOLE INSTALLATION EXTERNAL CONSOLE SPEAKER CONNECTION (OPTIONAL) With the Use an ◆Up to two 8-ohmspeakers can be used with each Console ◆Up to 150 feet of 22 AWG wire can be used with each speaker TELEPHONE LINE CONNECTION (OPTIONAL) Connect the Console to the telephone line if the system is monitored, requires Install a USOC RJ31-Xor RJ38-Xjack to the telephone system near the Console Route an appropriate modular telephone line cord from the jack to the Console Route the line cord through the Console’s wiring access hole (do not plug the transformer in until the wiring is complete) unswitched 6. BASIC CONSOLE PROGRAMMING PROGRAMMING DIFFERENT SENSOR TYPES press and hold the keypad’s ] key until programmed into the Console IMPORTANT NOTE: The NOTE: After the Console “learns” the transmitter 7.BASIC SENSOR INSTALLATION DXS-31& DXS-32DOOR/WINDOW SENSORS External normally closed switches The door/window sensor SET SENSOR JUMPER ◆A jumper inside the door/window sensor selects instant or delayed response 8.CUSTOMIZING THE CONSOLE 9. CONSOLE OPERATING MODES OFF MODE CHIME MODE START HERE (OPTIONAL) OR CHIME MODE START IN HOME MODE 1 GONG & 2 BEEPS AWAY MODE & 3 BEEPS QUICK ARM & 3 BEEPS DONE TEST MODE & 4 BEEPS 10.SYSTEM TROUBLE INDICATIONS 11.CUSTOMIZING THE SYSTEM will not SENSOR NUMBER FOR CHIME 8 FOR 8 TUV CHIME FUNCTION AWAY 1 BING START IN TEST MASTER 1 GONG & 5 BEEPS SENSOR 12. ADVANCED PROGRAMMING CHANGING A SENSORS SUPERVISION ◆Any sensor can be programmed as supervised or non-supervised CHANGING A SENSORS RESTORE REQUIREMENTS ◆Any sensor can be programmed as manual or automatic restore ENTRY DELAY TIME Page SILENT BURGLARY ALARMS ◆The factory setting causes audible burglary alarms ◆Alternately, the Console can be programmed for silent burglary alarms SILENT EMERGENCY ALARMS ◆The factory setting causes audible emergency alarms AUTOMATION OUTPUT MODE DURING ALARM AUTOMATION ACTIVATION TONE ◆Alternately, this sound can be silenced REMOTE CONTROL ARM/DISARM CHIRP ◆Alternately, these chirps can be silenced two or more digits different than any user code ADDITIONAL USER CODES ARM OR DISARM Log the restricted user codes in the boxes REMOVING USER CODES Any restricted, duress or page alert user code can be removed from the Console 13. COMMUNICATOR PROGRAMMING SETUP MODE GENERAL COMMUNICATOR OPTIONS COMMUNICATOR ENABLE 2-WAYAUDIO When the Model The audio module can be programmed for listen only CALL LIMITER DIALING DELAY DIALING METHOD The factory setting causes the communicator to dial using DTMF COMMUNICATOR REPORTING OPTIONS REPORTING FORMAT CALL ROUTING Communicator Reporting Option Table ACCOUNT NUMBER ◆The communicator’s account number entered must be 4-digitslong ◆The factory setting for the account number is ◆Enter an account number from 0000 to PRIMARY TELEPHONE NUMBER REPORT CONSOLE TROUBLE REPORT FORCE ARMING ◆The factory setting does not send force arming reports The factory set reporting code for force arming is “65” (Code 574 with Ademco) OPENING AND CLOSING REPORTS COMMUNICATOR REPORTING CODES ◆If Point ID reporting is enabled (the factory default setting), each sensor can report a unique alarm and trouble code ◆ If Point ID is disabled, the “general” reporting FORCE ARMING REPORTING CODE ◆Programming Step #258 ◆Any value from 0-99can be programmed for this event (0 = no report) DURESS REPORTING CODE ◆Programming Step #259 Page Point ID Reporting Codes Table IMPORTANT INFORMATION