Linear DVS-2400 42

4 BY 2 FORMAT POINT ID REPORTING CODES

4 BY 2 FORMAT POINT ID ALARM REPORT CODES

◆Refer to the 4 by 2 Format Point ID Reporting Code table to view/edit the alarm reporting codes for each of the 24 sensors. The

communicator will send these codes if Point ID is	2 ABC
	2 ABC
enabled and any sensor triggers an alarm. The		PROGRAMMING STEPS
enabled and any sensor triggers an alarm. The		#210 TO #233
factory settings are listed, along with a blank		#210 TO #233
factory settings are listed, along with a blank
area to write in the new installation values.		PROGRAM
✍NOTE: Be careful not to duplicate codes unless	HOME	PROGRAM
	HOME
the Central Station requires specific codes for		0 - 99 FOR SENSOR
certain types of sensors.		ALARM CODE
◆ Each programming function is performed with		(0 = NO REPORT)
◆ Each programming function is performed with	AWAY	STORE PROGRAM
similar keystrokes. After the system is in Setup		STORE PROGRAM
similar keystrokes. After the system is in Setup
Mode, enter the programming step number,
press the [HOME] key (HOME = program), enter
the new value, and press the [AWAY] key
(AWAY = store).

4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES

◆Refer to the 4 by 2 Format Point ID Reporting Code table to view/edit the trouble reporting

	codes for each of the 24 sensors. The	2 ABC
	codes for each of the 24 sensors. The		PROGRAMMING STEPS
	communicator will send these codes if Point ID is		PROGRAMMING STEPS
	communicator will send these codes if Point ID is		#234 TO 257
	enabled and any sensor has a low battery or
	trouble condition. The factory settings are listed,	HOME	PROGRAM
	along with a blank area to write in the new	HOME	PROGRAM
	along with a blank area to write in the new		0 - 99 FOR SENSOR
	installation values.		0 - 99 FOR SENSOR
	installation values.		TROUBLE CODE
	✍NOTE: Be careful not to duplicate codes unless		(0 = NO REPORT)
	the Central Station requires specific codes for	AWAY	STORE PROGRAM
	certain types of sensors.		STORE PROGRAM
	certain types of sensors.

◆Each programming function is performed with similar keystrokes. After the Console is in Setup Mode, enter the programming step number, press the [HOME] key (HOME = program), enter the new value, and press the [AWAY] key (AWAY = store).

40

Contents

Installation & Programming Instructions INTRODUCTION TABLE OF CONTENTS 1. THE DVS-2400SECURITY SYSTEM not both simultaneously are 2. SECURITY SYSTEM FLOOR PLAN 3. TYPICAL SYSTEM SENSORS 4. CONSOLE FEATURES Page 5. CONSOLE INSTALLATION EXTERNAL CONSOLE SPEAKER CONNECTION (OPTIONAL) With the Use an ◆Up to two 8-ohmspeakers can be used with each Console ◆Up to 150 feet of 22 AWG wire can be used with each speaker TELEPHONE LINE CONNECTION (OPTIONAL) Connect the Console to the telephone line if the system is monitored, requires Install a USOC RJ31-Xor RJ38-Xjack to the telephone system near the Console Route an appropriate modular telephone line cord from the jack to the Console Route the line cord through the Console’s wiring access hole (do not plug the transformer in until the wiring is complete) unswitched 6. BASIC CONSOLE PROGRAMMING PROGRAMMING DIFFERENT SENSOR TYPES press and hold the keypad’s ] key until programmed into the Console IMPORTANT NOTE: The NOTE: After the Console “learns” the transmitter 7.BASIC SENSOR INSTALLATION DXS-31& DXS-32DOOR/WINDOW SENSORS External normally closed switches The door/window sensor SET SENSOR JUMPER ◆A jumper inside the door/window sensor selects instant or delayed response 8.CUSTOMIZING THE CONSOLE 9. CONSOLE OPERATING MODES OFF MODE CHIME MODE START HERE (OPTIONAL) OR CHIME MODE START IN HOME MODE 1 GONG & 2 BEEPS AWAY MODE & 3 BEEPS QUICK ARM & 3 BEEPS DONE TEST MODE & 4 BEEPS 10.SYSTEM TROUBLE INDICATIONS 11.CUSTOMIZING THE SYSTEM will not SENSOR NUMBER FOR CHIME 8 FOR 8 TUV CHIME FUNCTION AWAY 1 BING START IN TEST MASTER 1 GONG & 5 BEEPS SENSOR 12. ADVANCED PROGRAMMING CHANGING A SENSORS SUPERVISION ◆Any sensor can be programmed as supervised or non-supervised CHANGING A SENSORS RESTORE REQUIREMENTS ◆Any sensor can be programmed as manual or automatic restore ENTRY DELAY TIME Page SILENT BURGLARY ALARMS ◆The factory setting causes audible burglary alarms ◆Alternately, the Console can be programmed for silent burglary alarms SILENT EMERGENCY ALARMS ◆The factory setting causes audible emergency alarms AUTOMATION OUTPUT MODE DURING ALARM AUTOMATION ACTIVATION TONE ◆Alternately, this sound can be silenced REMOTE CONTROL ARM/DISARM CHIRP ◆Alternately, these chirps can be silenced two or more digits different than any user code ADDITIONAL USER CODES ARM OR DISARM Log the restricted user codes in the boxes REMOVING USER CODES Any restricted, duress or page alert user code can be removed from the Console 13. COMMUNICATOR PROGRAMMING SETUP MODE GENERAL COMMUNICATOR OPTIONS COMMUNICATOR ENABLE 2-WAYAUDIO When the Model The audio module can be programmed for listen only CALL LIMITER DIALING DELAY DIALING METHOD The factory setting causes the communicator to dial using DTMF COMMUNICATOR REPORTING OPTIONS REPORTING FORMAT CALL ROUTING Communicator Reporting Option Table ACCOUNT NUMBER ◆The communicator’s account number entered must be 4-digitslong ◆The factory setting for the account number is ◆Enter an account number from 0000 to PRIMARY TELEPHONE NUMBER REPORT CONSOLE TROUBLE REPORT FORCE ARMING ◆The factory setting does not send force arming reports The factory set reporting code for force arming is “65” (Code 574 with Ademco) OPENING AND CLOSING REPORTS COMMUNICATOR REPORTING CODES ◆If Point ID reporting is enabled (the factory default setting), each sensor can report a unique alarm and trouble code ◆ If Point ID is disabled, the “general” reporting FORCE ARMING REPORTING CODE ◆Programming Step #258 ◆Any value from 0-99can be programmed for this event (0 = no report) DURESS REPORTING CODE ◆Programming Step #259 Page Point ID Reporting Codes Table IMPORTANT INFORMATION