12. ADVANCED PROGRAMMING
◆To perform any of the advanced programming steps, the Console must be in the Setup Mode.
◆Each programming function is performed with similar keystrokes. After the Console is in Setup Mode, enter the programming step number, press the [HOME] key (HOME = program), enter the new value, and press the [AWAY] key (AWAY = store). Follow the figures next to the programming steps.
| HOME = PROGRAM | TEST = REMOVE |
Start with the Console in Test Mode (Setup Mode cannot be reached from any other mode).
From Test Mode, enter the master user code then press [TEST].✍NOTE: Only the master user code can be used to put the Console into the Setup Mode. The restricted user codes cannot access Setup Mode.
❇A “gong” and five “beeps” will sound, signaling that the Console is in Setup Mode.
Hold the [OFF] key for three seconds when you want to exit Setup Mode.✍NOTE: If the Console is left unattended in Setup Mode, it will automatically switch back to Off Mode after three minutes.
CONSOLE PROGRAMMING OPTIONS
STEP # | PROGRAMMING FUNCTION |
| POSSIBLE VALUES | FACTORY VALUE | INSTALLATION VALUE |
|
|
|
|
| |
25 | ENTRY DELAY | 30 |
| ||
26 | EXIT DELAY | 60 |
| ||
30 | BURGLARY SIREN TIME | 5 |
| ||
31 | EMERGENCY SIREN TIME | 5 |
| ||
32 | FIRE SIREN TIME | 5 |
| ||
40 | AUTOMATION OUTPUT TIME | 0 |
| ||
50 | REMOTE ARMING MODE | 2 | = HOME MODE; 3 = AWAY MODE | 3 |
|
51 | REMOTE DISARMING MODE | 0 | = OFF MODE; 1 = CHIME MODE | 0 |
|
61 | ENTRY DELAY BEEPS | 0 | = OFF; 1 = ON | 1 |
|
62 | EXIT DELAY BEEPS | 0 | = OFF; 1 = ON | 1 |
|
63 | SILENT BURGLARY ALARM | 0 | = AUDIBLE; 1 = SILENT | 0 |
|
64 | SILENT EMERGENCY ALARM | 0 | = AUDIBLE; 1 = SILENT | 0 |
|
65 | QUICK ARMING | 0 | = OFF; 1 = ON | 1 |
|
66 | AUTO RESTORE | 0 | = OFF; 1 = ON | 1 |
|
67 | AUTO BYPASS | 0 | = OFF; 1 = ON | 0 |
|
68 | AUTOMATION MODE DURING ALARM | 0 | = FLASH (ENABLED BY FUNCTION 72) | 0 |
|
1 | = STEADY (ENABLED BY FUNCTION 72) |
| |||
|
|
|
| ||
69 | AUTOMATION BING TONE | 0 | = NO BINGS | 1 |
|
1 | = BINGS |
| |||
|
|
|
| ||
70 | REMOTE ARM/DISARM CHIRP | 0 | = NO CHIRPS | 1 |
|
1 | = CHIRPS (1 CHIRP = ARMED, 2 CHIRPS = DISARMED) |
| |||
|
|
|
| ||
71 | AUTOMATION FLASHES AFTER ALARM | 0 | = STANDARD | 0 |
|
1 | = FLASHING AFTER ALARM |
| |||
|
|
|
| ||
|
| 0 | = STANDARD |
|
|
72 | AUTOMATION ACTIVE DURING ALARM | 1 | = AUTOMATION ACTIVE DURING ALARM | 0 |
|
|
| (FLASH OR STEADY PROGRAMMED BY FUNCTION 68) |
|
| |
73 | AUTOMATION ON WHILE ARMED | 0 | = STANDARD | 0 |
|
1 | = ON WHILE ARMED |
| |||
|
|
|
| ||
74 | AUTOMATION ON DURING EXIT/ENTRY | 0 | = STANDARD | 0 |
|
1 | = ON DURING EXIT/ENTRY DELAYS |
| |||
|
|
|
| ||
75 | AUTOMATION POLARITY | 0 | = + WHEN OFF; 1 = + WHEN ON | 1 |
|
87 | REMOTE ACCESS PASSWORD | 6 DIGITS | 987654 |
| |
92 | DURESS CODE | REMOVED |
| ||
93 | RESTRICTED USER CODE #1 | REMOVED |
| ||
94 | RESTRICTED USER CODE #2 | REMOVED |
| ||
95 | RESTRICTED USER CODE #3 | REMOVED |
| ||
96 | RESTRICTED USER CODE #4 | REMOVED |
| ||
97 | RESTRICTED USER CODE #5 | REMOVED |
| ||
98 | PAGE ALERT USER CODE | REMOVED |
| ||
99 | MASTER USER CODE | 1234 |
| ||
25