Manuals / Brands / Household Appliance / Home Security System / Linear / Household Appliance / Home Security System

Linear DVS-2400 EXIT DELAY TIME, ENTRY DELAY TIME, BURGLARY SIREN TIME, EMERGENCY SIREN TIME, CHANGING A SENSORS SUPERVISION, CHANGING A SENSORS RESTORE REQUIREMENTS

1 44

Download 44 pages, 2.58 Mb

CHANGING A SENSORS SUPERVISION

◆When a sensor is programmed, the Console sets all stationary sensors as supervised, and all portable sensors as non-supervised.

◆The Console expects hourly status transmissions from any sensor programmed as supervised.

◆Any sensor can be programmed as supervised or non-supervised.

✍NOTE: Don’t program a sensor that doesn’t send status transmissions as supervised.

SENSOR NUMBER

TO CHANGE

HOME PROGRAM

16 FOR NON-SUPERVISED

17 FOR SUPERVISED

AWAY STORE PROGRAM

CHANGING A SENSORS RESTORE REQUIREMENTS

◆When a sensor is programmed, the Console automatically recognizes it as manually or automatically restoring.

◆The Console expects restoral signals from any sensor programmed as manual restore.

◆Any sensor can be programmed as manual or automatic restore.

✍NOTE: Don’t program a sensor that doesn’t send restoral transmissions as manual restore.

SENSOR NUMBER

TO CHANGE

HOME PROGRAM

18 FOR MANUAL RESTORE

19 FOR AUTO RESTORE

AWAY STORE PROGRAM

ENTRY DELAY TIME◆The factory-set Entry Delay time is 30 seconds.◆The Entry Delay time can be adjusted from 20 to 255 seconds.

✍NOTE: Don’t make the Entry Delay too short. The user may not have enough time to disarm the system before an alarm.

Write the new Entry Delay time in the User’s Guide.

PROGRAMMING STEP #25

JKL

PROGRAM

TIME IN SECONDS (20-255)

STORE PROGRAM

EXIT DELAY TIME◆The factory-set Exit Delay time is 60 seconds.◆The Exit Delay time can be adjusted from 20 to 255 seconds. Write the new Exit Delay time in the User’s Guide.

PROGRAMMING STEP #26

PROGRAM

AWAY

TIME IN SECONDS (20-255)

STORE PROGRAM

BURGLARY SIREN TIME◆The factory-set burglary siren time is five minutes.◆The burglary siren time can be adjusted from one to 30 minutes.

3DEF

PROGRAMMING STEP #30

0
HOME	PROGRAM
	TIME IN MINUTES (1-30)
AWAY	STORE PROGRAM

EMERGENCY SIREN TIME◆The factory-set emergency siren time is five minutes.◆The emergency siren time can be adjusted from one to 30 minutes.

3DEF

PROGRAMMING STEP #31

1

HOME PROGRAM

TIME IN MINUTES (1-30)

AWAY STORE PROGRAM

26

Contents

Installation & Programming Instructions INTRODUCTION TABLE OF CONTENTS 1. THE DVS-2400SECURITY SYSTEM not both simultaneously are 2. SECURITY SYSTEM FLOOR PLAN 3. TYPICAL SYSTEM SENSORS 4. CONSOLE FEATURES Page 5. CONSOLE INSTALLATION EXTERNAL CONSOLE SPEAKER CONNECTION (OPTIONAL) With the Use an ◆Up to two 8-ohmspeakers can be used with each Console ◆Up to 150 feet of 22 AWG wire can be used with each speaker TELEPHONE LINE CONNECTION (OPTIONAL) Connect the Console to the telephone line if the system is monitored, requires Install a USOC RJ31-Xor RJ38-Xjack to the telephone system near the Console Route an appropriate modular telephone line cord from the jack to the Console Route the line cord through the Console’s wiring access hole (do not plug the transformer in until the wiring is complete) unswitched 6. BASIC CONSOLE PROGRAMMING PROGRAMMING DIFFERENT SENSOR TYPES press and hold the keypad’s ] key until programmed into the Console IMPORTANT NOTE: The NOTE: After the Console “learns” the transmitter 7.BASIC SENSOR INSTALLATION DXS-31& DXS-32DOOR/WINDOW SENSORS External normally closed switches The door/window sensor SET SENSOR JUMPER ◆A jumper inside the door/window sensor selects instant or delayed response 8.CUSTOMIZING THE CONSOLE 9. CONSOLE OPERATING MODES OFF MODE CHIME MODE START HERE (OPTIONAL) OR CHIME MODE START IN HOME MODE 1 GONG & 2 BEEPS AWAY MODE & 3 BEEPS QUICK ARM & 3 BEEPS DONE TEST MODE & 4 BEEPS 10.SYSTEM TROUBLE INDICATIONS 11.CUSTOMIZING THE SYSTEM will not SENSOR NUMBER FOR CHIME 8 FOR 8 TUV CHIME FUNCTION AWAY 1 BING START IN TEST MASTER 1 GONG & 5 BEEPS SENSOR 12. ADVANCED PROGRAMMING CHANGING A SENSORS SUPERVISION ◆Any sensor can be programmed as supervised or non-supervised CHANGING A SENSORS RESTORE REQUIREMENTS ◆Any sensor can be programmed as manual or automatic restore ENTRY DELAY TIME Page SILENT BURGLARY ALARMS ◆The factory setting causes audible burglary alarms ◆Alternately, the Console can be programmed for silent burglary alarms SILENT EMERGENCY ALARMS ◆The factory setting causes audible emergency alarms AUTOMATION OUTPUT MODE DURING ALARM AUTOMATION ACTIVATION TONE ◆Alternately, this sound can be silenced REMOTE CONTROL ARM/DISARM CHIRP ◆Alternately, these chirps can be silenced two or more digits different than any user code ADDITIONAL USER CODES ARM OR DISARM Log the restricted user codes in the boxes REMOVING USER CODES Any restricted, duress or page alert user code can be removed from the Console 13. COMMUNICATOR PROGRAMMING SETUP MODE GENERAL COMMUNICATOR OPTIONS COMMUNICATOR ENABLE 2-WAYAUDIO When the Model The audio module can be programmed for listen only CALL LIMITER DIALING DELAY DIALING METHOD The factory setting causes the communicator to dial using DTMF COMMUNICATOR REPORTING OPTIONS REPORTING FORMAT CALL ROUTING Communicator Reporting Option Table ACCOUNT NUMBER ◆The communicator’s account number entered must be 4-digitslong ◆The factory setting for the account number is ◆Enter an account number from 0000 to PRIMARY TELEPHONE NUMBER REPORT CONSOLE TROUBLE REPORT FORCE ARMING ◆The factory setting does not send force arming reports The factory set reporting code for force arming is “65” (Code 574 with Ademco) OPENING AND CLOSING REPORTS COMMUNICATOR REPORTING CODES ◆If Point ID reporting is enabled (the factory default setting), each sensor can report a unique alarm and trouble code ◆ If Point ID is disabled, the “general” reporting FORCE ARMING REPORTING CODE ◆Programming Step #258 ◆Any value from 0-99can be programmed for this event (0 = no report) DURESS REPORTING CODE ◆Programming Step #259 Page Point ID Reporting Codes Table IMPORTANT INFORMATION