Manuals / Brands / Household Appliance / Home Security System / Linear / Household Appliance / Home Security System

Linear DVS-2400 Any value from, DURESS REPORTING CODE, ◆Programming Step #258, ◆Programming Step #259, FORCE ARMING REPORTING CODE, System Reporting Codes Table

1 44

Download 44 pages, 2.58 Mb

FORCE ARMING REPORTING CODE◆Programming Step #258

◆The factory set reporting code for force arming is “65” (Code 574 with Ademco).

◆Any value from 0-99 can be programmed for this event (0 = no report).

✍NOTE: For force arming reporting, force arming reports must be enabled. See Page 37.

2ABC

5 JKL

PROGRAMMING STEP #258

8TUV

HOME PROGRAM

0 - 99 FOR FORCE ARMING REPORTING CODE

AWAY STORE PROGRAM

DURESS REPORTING CODE◆Programming Step #259◆The factory set reporting code for Duress is “66” (Code 121 with Ademco).

◆Any value from 0-99 can be programmed for this event (0 = no report).

✍NOTE: For duress code reporting a keypad duress code must be programmed. See Page 30.

2ABC

5 JKL

PROGRAMMING STEP #259

9WXY

HOME PROGRAM

0 - 99 FOR DURESS CODE

AWAY STORE PROGRAM

SYSTEM REPORTING CODES

	STEP #	PROGRAMMING	POSSIBLE	FACTORY	ADEMCO	INSTALLATION
	STEP #	FUNCTION	4 x 2 VALUES	4 x 2 VALUE	VALUE	4 x 2 VALUE
		FUNCTION	4 x 2 VALUES	4 x 2 VALUE	VALUE	4 x 2 VALUE

	261	SYSTEM FIRE REPORT CODE	0 - 99	68	110
	262	SYSTEM EMERGENCY REPORT CODE	0 - 99	69	120
	263	SYSTEM TEST/CANCEL REPORT CODE	0 - 99	70	406
	264	SYSTEM LOW BATTERY RESTORAL REPORT CODE	0 - 99	71	R302
	266	SYSTEM LOW BATTERY REPORT CODE	0 - 99	73	E302

	258	FORCE ARMING REPORT CODE	0 - 99	65	574
	259	DURESS REPORT CODE	0 - 99	66	121

System Reporting Codes Table

OPENING & CLOSING REPORTING CODES TABLE

USER CODE	4 x 2 CLOSING	4 x 2 OPENING	ADEMCO CLOSING		ADEMCO OPENING
USER CODE	(ARMING) CODE	(DISARMING) CODE	(ARMING) CODE		(DISARMING) CODE
	(ARMING) CODE	(DISARMING) CODE	(ARMING) CODE		(DISARMING) CODE

MASTER USER CODE	74	82	R401	C000	E401	C000
RESTRICTED USER CODE #1	75	83	R401	C001	E401	C001
RESTRICTED USER CODE #2	76	84	R401	C002	E401	C002
RESTRICTED USER CODE #3	77	85	R401	C003	E401	C003
RESTRICTED USER CODE #4	78	86	R401	C004	E401	C004
RESTRICTED USER CODE #5	79	87	R401	C005	E401	C005
PAGE ALERT USER CODE		(DIALS PAGE NUMBER ONLY, NO CODES REPORTED)
REMOTE/HARDWIRE ARM (SENSOR TYPE 9) & QUICK ARM	81		R407	C007
REMOTE/HARDWIRE DISARM (SENSOR TYPE 9)		89			E407	C007

Opening & Closing Reporting Codes Table

39

Contents

Installation & Programming Instructions INTRODUCTION TABLE OF CONTENTS 1. THE DVS-2400SECURITY SYSTEM not both simultaneously are 2. SECURITY SYSTEM FLOOR PLAN 3. TYPICAL SYSTEM SENSORS 4. CONSOLE FEATURES Page 5. CONSOLE INSTALLATION EXTERNAL CONSOLE SPEAKER CONNECTION (OPTIONAL) With the Use an ◆Up to two 8-ohmspeakers can be used with each Console ◆Up to 150 feet of 22 AWG wire can be used with each speaker TELEPHONE LINE CONNECTION (OPTIONAL) Connect the Console to the telephone line if the system is monitored, requires Install a USOC RJ31-Xor RJ38-Xjack to the telephone system near the Console Route an appropriate modular telephone line cord from the jack to the Console Route the line cord through the Console’s wiring access hole (do not plug the transformer in until the wiring is complete) unswitched 6. BASIC CONSOLE PROGRAMMING PROGRAMMING DIFFERENT SENSOR TYPES press and hold the keypad’s ] key until programmed into the Console IMPORTANT NOTE: The NOTE: After the Console “learns” the transmitter 7.BASIC SENSOR INSTALLATION DXS-31& DXS-32DOOR/WINDOW SENSORS External normally closed switches The door/window sensor SET SENSOR JUMPER ◆A jumper inside the door/window sensor selects instant or delayed response 8.CUSTOMIZING THE CONSOLE 9. CONSOLE OPERATING MODES OFF MODE CHIME MODE START HERE (OPTIONAL) OR CHIME MODE START IN HOME MODE 1 GONG & 2 BEEPS AWAY MODE & 3 BEEPS QUICK ARM & 3 BEEPS DONE TEST MODE & 4 BEEPS 10.SYSTEM TROUBLE INDICATIONS 11.CUSTOMIZING THE SYSTEM will not SENSOR NUMBER FOR CHIME 8 FOR 8 TUV CHIME FUNCTION AWAY 1 BING START IN TEST MASTER 1 GONG & 5 BEEPS SENSOR 12. ADVANCED PROGRAMMING CHANGING A SENSORS SUPERVISION ◆Any sensor can be programmed as supervised or non-supervised CHANGING A SENSORS RESTORE REQUIREMENTS ◆Any sensor can be programmed as manual or automatic restore ENTRY DELAY TIME Page SILENT BURGLARY ALARMS ◆The factory setting causes audible burglary alarms ◆Alternately, the Console can be programmed for silent burglary alarms SILENT EMERGENCY ALARMS ◆The factory setting causes audible emergency alarms AUTOMATION OUTPUT MODE DURING ALARM AUTOMATION ACTIVATION TONE ◆Alternately, this sound can be silenced REMOTE CONTROL ARM/DISARM CHIRP ◆Alternately, these chirps can be silenced two or more digits different than any user code ADDITIONAL USER CODES ARM OR DISARM Log the restricted user codes in the boxes REMOVING USER CODES Any restricted, duress or page alert user code can be removed from the Console 13. COMMUNICATOR PROGRAMMING SETUP MODE GENERAL COMMUNICATOR OPTIONS COMMUNICATOR ENABLE 2-WAYAUDIO When the Model The audio module can be programmed for listen only CALL LIMITER DIALING DELAY DIALING METHOD The factory setting causes the communicator to dial using DTMF COMMUNICATOR REPORTING OPTIONS REPORTING FORMAT CALL ROUTING Communicator Reporting Option Table ACCOUNT NUMBER ◆The communicator’s account number entered must be 4-digitslong ◆The factory setting for the account number is ◆Enter an account number from 0000 to PRIMARY TELEPHONE NUMBER REPORT CONSOLE TROUBLE REPORT FORCE ARMING ◆The factory setting does not send force arming reports The factory set reporting code for force arming is “65” (Code 574 with Ademco) OPENING AND CLOSING REPORTS COMMUNICATOR REPORTING CODES ◆If Point ID reporting is enabled (the factory default setting), each sensor can report a unique alarm and trouble code ◆ If Point ID is disabled, the “general” reporting FORCE ARMING REPORTING CODE ◆Programming Step #258 ◆Any value from 0-99can be programmed for this event (0 = no report) DURESS REPORTING CODE ◆Programming Step #259 Page Point ID Reporting Codes Table IMPORTANT INFORMATION