Linear DVS-2400 Automation Output, Programmable Options, the Automation Output, TELEPHONE LINE CONNECTION (OPTIONAL), armed, or, on during exit/entry delays

TELEPHONE LINE CONNECTION (OPTIONAL)

◆Connect the Console to the telephone line if the system is monitored, requires 2-way audio, or requires telephone remote command.

◆Telephone ring & tip terminals are for connection to the incoming telephone line.

◆Seized telephone ring & tip are for connection to local telephone sets. When the communicator activates, all the local telephone sets will be disconnected to prevent an off-hook telephone on the premises from blocking the communicator call.

Install a USOC RJ31-X or RJ38-X jack to the telephone system near the Console. Route an appropriate modular telephone line cord from the jack to the Console. Route the line cord through the Console’s wiring access hole.

Connect the incoming telephone line wires to the Console’s telephone terminal block TIP and RING terminals.

◆Connect the local telephone set wires to the Console’s telephone terminal block SEIZED TIP and SEIZED RING terminals.

◆When directly connecting (without a telephone line) to the DVS-2400 with the RA-2400 remote access software (Version 1.3 or later), disconnect the incoming telephone line and connect the modem to the panel’s TIP and RING terminals (with the modem’s red & green phone line wires). Press the [EMERGENCY] key while in Test Mode to cause the panel to connect to the modem.

TELEPHONE

TERMINAL LINEAR SECURITY CONSOLE MODEL DVS-2400

BLOCK

			TELEPHONE TERMINAL BLOCK
		SEIZED RING			TIP
		SEIZED TIP			RING
		TO LOCAL		R T R1 T1	TO PHONE
OPTIONAL		PHONES			LINE
VOICE MODULE
MODEL: VB-2 OR VB-3
SEIZED	SEIZED	LINE	LINE
TIP (T1)	RING (R1)	TIP (T)	RING (R)

DVS-2400

TELEPHONE

TERMINAL

BLOCK

BROWN

RED

GRAY GREEN

8-PIN										BLUE, ORANGE
MODULAR
PHONE CORD										BLACK, AND
										YELLOW NOT
										USED
8-POSITION		R1			R	T			T1	SHORTING BAR
USOC RJ31-X										SHORT REMOVED
(OR RJ38-X)										ON PLUG
JACK		1	2	3	4	5	6	7	8	INSERTION
	R									T1	TO LOCAL
TO TELEPHONE	T
											TELEPHONE
										R1
NETWORK											SETS

CONNECT TELEPHONE LINE

TO THE TELEPHONE

TERMINAL BLOCK

AUTOMATION OUTPUT CONNECTION (OPTIONAL)

◆The Console provides a Automation Output to control lights, devices and appliances.

◆Automation Output can connect to most popular home automation devices and other simple electronic devices (see Figure).

Press [(A)] to turn the Automation Output on, press [(A)] again to turn it off.Programmable Options

◆ There are many programmable options for the

Automation Output.

◆ The Automation Output can be programmed for

LINEAR SECURITY CONSOLE MODEL DVS-2400

MAIN

TERMINAL

BLOCKOPTIONAL VOICE MODULE

MODEL: VB-2 OR VB-3

MINUS H/A TERMINAL WILL SWITCH TO GROUND WHEN AUTOMATION OUTPUT IS ACTIVATED

MAIN TERMINAL BLOCK

	AC
LIGHT EMITTING	AC
	EXT. SPKR
DIODE (L.E.D.)	(-)
	H/A -
	H/A +
	RELAY N.O.
	RELAY DRY

POSITIVE H/A TERMINAL PROVIDES +12 VOLTS DC AND IS CURRENT LIMITED AT 30 MILLIAMPS MAXIMUM

a variety of useful functions, such as: flashing

during alarm, flashing after an alarm, on while

armed, or, on during exit/entry delays.

◆ See the “Advanced Programming” section of this

manual for details on changing the function of

the Automation Output.

10

EXAMPLE AUTOMATION OUTPUT HOOK-UPS

	X-10	LINEAR RB-90
X-10	BURGLAR ALARM
		RELAY MODULE
	INTERFACE		YOUR
	(CAN CONTROL		LOAD	LIGHT
	HOUSE LIGHTS
				EMITTING
	THROUGH X-10
				DIODE
	SYSTEM)
				(L.E.D.)
			POWER
			SOURCE
H/A + H/A -		H/A + H/A -		H/A + H/A -