Mitsubishi Electronics FR-F700 instruction manual Option and Peripheral Devices, Options

Option and Peripheral Devices

Options

By fitting the following options to the inverter, the inverter is provided with more functions. One plug-in option can be fitted.

Plug-in Type

Stand-alone Shared

	Name	Type		Applications, Specifications, etc.			Applicable
							Inverter
			⋅	This input interface sets the high frequency accuracy of the
				inverter using an external BCD or binary digital signal.
16-bit digital input		FR-A7AX		BCD code 3 digits (maximum 999)
				BCD code 4 digits (maximum 9999)
				Binary 12 bits (maximum FFFH)
				Binary 16 bits (maximum FFFFH)
			⋅	This option provides the inverter with open collector outputs
				selected from among the standard output signals.
Digital output		FR-A7AY	⋅	This option adds two	different signals that can	be
extension analog output				monitored at the terminals FM and AM, such as the output			Shared among all
				frequency, output voltage and output current.			models
			⋅	20mADC or 5VDC (10V) meter can be connected.
Relay output		FR-A7AR	⋅	Output any three output signals available with the inverter
				as standard from the relay contact terminals
Communication	LONWORKS	FR-A7NL		only.
	CC-LINK	FR-A7NC	⋅	This option allows the inverter to be operated or monitored
				or the parameter setting to be changed from a computer or
				PLC.
			* For the FR-A7NC (CC-Link), the above operations can be done from the PLC
		FR-PU04	Interactive parameter unit with LCD display
Parameter unit (Eightlanguages)
Parameter unit connection cable		FR-CB20￿	Cable for connection of operation panel or parameter unit				Shared among all
			￿ indicates a cable length. (1m, 3m, 5m)
							models
Operation panel connection		FR-ADP	Connector to connect the operation panel (FR-DU07) and
connector			connection cable
		FR-AAT	Attachment for replacing		with the F700 series using	the
			installation holes of the FR-F500.
							According to
Intercompatibility attachment
		FR-A5AT	Attachment for replacing with the F700 series using the				capacities
			installation holes of the FR-A100<Excellent> and FR-
			A200<Excellent>
AC reactor		FR-HAL	For harmonic current reduction and inverter input power factor				For 200V class
							55K or less, 400V
			improvement (total power factor approx. 88%)				class 75K or less
DC reactor		FR-HEL	For harmonic current reduction and inverter input power factor				For the 55K or
			improvement (total power factor approx. 93%)				less
Line noise filter		FR- BSF01	For line noise reduction				Shared among all
		FR- BLF					models
BU type brake unit		BU	For increasing the braking capability of the inverter (for high-				For the 55K or
			inertia load or negative load)				less
Brake unit		FR-BU	For increasing the braking capability of the inverter (for high-
		MT-BU5					According to
		FR-BR	inertia load or negative load)				capacities
Resistor unit			Brake unit and resistor unit are used in combination
		MT-BR5
Power regeneration common		FR-CV
converter			Unit which can return motor-generated braking energy back				For the 55K or
Dedicated stand-alone reactor		FR-CVL	to the power supply in common converter system				less
for the FR-CV
Power regeneration converter		MT-RC	Energy saving type high performance brake unit which can				For the 75K or
			regenerate the braking energy generated by the motor to the				more
			power supply.
		FR-HC	The high power factor converter switches the converter				According to
High power factor converter			section on/off to reshape an input current waveform into a
		MT-HC	sine wave, greatly suppressing harmonics. (Used in				capacities
			combination with the standard accessory.)
Surge voltage suppression filter		FR-ASF	Filter for suppressing surge voltage on motor				For 400V class
							55K or less
Sinewave filter	Reactor	MT-BSL	Reduce the motor noise during inverter driving				For the 75K or
	Capacitor	MT-BSC	Use in combination with a reactor and a capacitor				more

49