SG2 LR Optical Receiver | Motorola SG 2000 guide

5 - 1 0

O p e r a t i o n

Cleaning the Optical Connector

The design of the SG 2000 optical module connector enables you to clean it easily without removing the module from the node.

To clean the connector:

1If necessary, disconnect the service cable from the modules’ optical-connector assembly. Place a dust cover on the service cable connector.

2Lift the metal tab to release the optical-connector assembly and pull it out of the module.

CAUTION!

Do not pull the optical connector out more than two inches from the casting wall. If you pull the connector out too far, you must disassemble the module and respool the fiber.

3Remove the bulkhead adapter from the internal optical connector.

4Carefully clean the optical connector and bulkhead adapter using a suitable optical connector cleaning kit. If an optical connector cleaning kit is not available, clean the connector using pure isopropyl alcohol (99%) and a lint-free wipe. Dry it with filtered compressed air. You can also clean the bulkhead adapter using filtered compressed air.

5Re-assemble the bulkhead adapter to the internal optical connector. Ensure that you install the internal optical connector in the end of the bulkhead adapter bearing the metal tangs.

6Snap the optical connector assembly back into the module.

7If necessary, clean and reconnect the service cable.

SG2 - LR Optical Receiver

The SG2-LR is a line of forward-path optical receivers used in the SG 2000 node platform. It is designed to be used in conjunction with an AM-Blazer, AM-OMNI-LM*, MegaStar, or other similar optical transmitter.

Figure 5-13 illustrates the SG2-LR:

Figure 5-13

SG2-LR

	Receiver			OPTICAL
				POWER
SG2-LR	HYBRID	O	F	L	N	H
	HYBRID	N	A	O	O	I
	CURRENT		U	W	R	G
ASSEM BLED	(1 V/A)		L		M	H
IN MEXICO	(1 V/A)		T
IN MEXICO			T

SG 2000 Installation and O peration Manual

Image 74

Motorola SG 2000 operation manual SG2 LR Optical Receiver, Cleaning the Optical Connector

Contents

A R L I N E Special Symbols that Might Appear on the Equipment Contents Installation E r a t i o n Specification s Torque Specifications Abbreviations and Acronyms SG2-LR Tables N t e n t s Section SG 2000 closed Features include SG 2000 open Using this Manual Related Documentation Bold type Document ConventionsIf You Need Help Calling for Repairs Mounting Holes HousingSG 2000 housing dimensions front and side view Port Locations Port locations Housing gaskets Gaskets Power Supply SG2-PS2 power supply Configuration Network Monitoring To suit system requirements the RF chassis cover. notation Signal flow diagram Forward Path E r v i e w SG2-LR receiver functional diagram SG2-LR Receiver Model Description Analog Return PathAnalog Return Transmitters Analog return transmitters SG2 transmitter block diagram JXP Digital Return Path Digital return transmitters DS-SG2-DRT-2X/A Level Control Options and AccessoriesOptions and accessories Model Description Function SG2 SG2-SBSG2-PS2 SG2-FE Gain Selection Optical input versus 750 MHz gain 10 illustrates the gain option selection chart for 870 MHz Optical input versus 870 MHz gain Tilt Selection Relative level dB versus 750 MHz slope 77 channels SG2 870 MHz Slope Chart Analog Channels, 220 MHz Digital Relative level dB versus 870 MHz slope 94 channels SG2 870 MHz Slope Chart Analog Channels, 120 MHz Digital Relative level dB versus 870 MHz slope 110 channels N c h S e t u p G u r e 3 2 0 0 0 R F c h a s s i s W e r i n g t h e N o d e Fuse Functi o n Rati ng Ype W e r S u p p l y S e t t i n g s Illustrates the location of the LO-HIjumper Single Power Supply or Commonly Po wered Redundant Supplies I c k C h e c k s F u n c t i o n a l T e s t i n g N u a l G a i n C o n t r o l Analog Retu rn Path R w a r d P a t h P a d d i n g B l e 3 2 0 0 0 p a d c h a r t s t a n d a r d g a i n B l e 3 2 0 0 0 p a d c h a r t h i g h g a i n G u r e 3 N k P e r f o r m a n c e G u r e 3 1 N c h S e t u p Install i n g t h e D S S G 2 D R R B B o a r d O p t i o n G u r e 3 1 S G 2 D R R B b o a r d Install e d G u r e 3 1 C a t i o n o f J X P s o n E p a c k Digital Transmitter Install i n g t h e S t a t u s M o n i t o r O p t i o n 2 0 0 0 a c t i v a t i o n W o r k s h e e t DC powering Service cable connection and compression fitting Splicing Fiber Installation Strand Wire Mounting Mounting bracket-front view Mounting bracket-rear and side views Center conductor length Coaxial CablesFiber Cables Housing lid and fiber spool tray Fiber spool tray Installation Forward Path RF Configuration Single Receiver Mode Redundant receiver Redundant Receiver ModeBroadband/Narrowcast Mode Broadband/narrowcast AB Override Functionality Override Status Monitor/Manual Control Operation Status monitor/MCB operation Split return Analog Return Path RF ConfigurationRedundant return RF chassis and location of the SG2-RPM/C or SG2-RPM/S board Digital Return Path RF Configuration DS-SG2-DRT/A redundant return DS-SG2-DRT-2X/A split return DS-SG2-DRT-2X/A redundant return Removing SG 2000 Optical Modules Installing SG 2000 Optical ModulesSG 2000 Optical Modules Cleaning the Optical Connector SG2 LR Optical Receiver Feature Description Test-point voltage versus optical power 0.3 Wavelength Selection Jumper Wavelength selection jumper SG2 Ifpt Optical Transmitter FeatureDescriptionSG2-IFPT features SG2 FPT Optical Transmitter Transmitter enableSG2-FPT features SG2-DFBT features SG2 Dfbt Optical Transmitter Single red LED that lights if the hybrid current is outside SG2-DFBT/3 features SG2 DFBT/3 Optical Transmitter SG2-EIFPT features SG2 Eifpt Optical Transmitter DS SG2 DRT/A Digital Return Transmitter DS-SG2-DRT/A Feature DS-SG2-DRT/A features DS SG2 DRT 2X/A Digital Return Transmitter DS-SG2-DRT-2X/A DS-SG2-DRT-2X/A features DS-SG2-DRT-2X/A cable connector DS-SG2-DRT-2X/A installed in SG DS-SG2-DRT-2X/A second RF input cable connection SG2-PS Power SupplySG2-PS power supply Status Monitoring Parameter Description Manual Control Board Description Function Potentiometers ICS1 Alarm test pointDB test point Through ICS4 Off Ingress ControlState Description Table A-2 Station RF characteristics Parameter SpecificationTable A-1 SG 2000 optical characteristics Appendix a ParameterSpeci fic ation Parameter Table A-5 SG2-IFPT RF specificationsTable A-6 SG2-FPT RF specifications Table A-7 SG2-DFBT RF specifications Table A-8 SG2-DFBT/3 RF specifications Table A-9 SG2-EIFPT RF specifications Table A-10 SG2-DRT/A RF specifications Minimum Optical Model Output Power DBm Table A-11 SG2-DRT-2X/A RF specifications Option Watts ac Amps Power @90V @60V @52V @44V Table A-15 SG2-87 performance, with 94 channels Channels Link Launch SystemTable A-14 SG2-75 performance, with 77 channels Table A-16 SG2-87 performance, with 110 channels Torque Fastener Screw Size Wrench Size In-lbs Ft-lbs DBmV DBcDBm MHz National Television Standards Committee Return for service authorizationSnap connector Optical modulation index Mgbi