Negotiation display enabled, DTR disconnects | Motorola V.3600

Command Index and Defaults

Table E-1. Synchronous Command Reference (Continued)

Command	Page	S-Reg	Description
W	5-6	S82	Negotiation display disabled

W1		S82	Negotiation display enabled

W2		S82	Displays DCE link rate

X		S22	CONNECT (code 1), for all speeds, no dial
			tone or busy signal detection

X1		S22	Appropriate connect codes for rate, no dial
			tone detection

X2		S22	Wait for dial tone (appropriate
			connect codes)

X3		S22	Detect busy signal (appropriate
			connect codes)

X4		S22	Wait for dial tone, detect busy signal
			(appropriate connect codes)

Y	5-25	S21	Long space disconnect disabled

Y1		S21	Long space disconnect enabled

Z	5-39	--	Reset to user option set #1 †

Z1		--	Reset to user option set #2 †

&C	5-19	S21	DCD always on

&C1		S21	DCD on while carrier is present

&C2		S21	DCD off 5 seconds after disconnect

&C3		S21	DCD follows remote RTS

&D	5-20	S21	DTR ignored

&D1		S21	DTR recalls command mode

&D2		S21	DTR disconnects

&D3	5-20	S21	DTR disconnects and resets modem to stored
			configuration

&F or &F1	5-39	--	Restore factory configuration 1 †

&F2		--	Restore factory configuration 2 †

&F3		--	Restore factory configuration 3 †

&F4		--	Restore factory configuration 4 †

&F5		--	Restore factory configuration 5 †

&F6		--	Restore factory configuration 6 †

&F7		--	Restore factory configuration 7 †

&F8		--	Restore factory configuration 8 †

&F9		--	Restore factory configuration 9 †

&G	5-25	S23	No guard tone

&G1		S23	550 Hz tone

&G2		S23	1800 Hz tone

† cannot be executed from remote configuration mode

V.3600

E-3

Image 205

Motorola V.3600 manual Negotiation display enabled, Wait for dial tone, detect busy signal, Appropriate connect codes

Contents

Modem User’s Guide 3600Motorola Copyright UpdatesTrademarks FCC Requirements Regulatory Information FCC Fax Branding Requirements FCC Part 15 Declaration Of ConformityModel Name V.3600, 115 VAC version only Model Name V.3600, all other versions Shielded Cables Industry Canada IC Requirements Special Requirements For Canada Canadian Emission Requirements V.3600, other versions Ringer Equivalence NumberPage Contents Contents Contents Protocols Test Mode Operation Security Status Registers Fax Operation Contents 25 bis Autodialer Appendix A. Specifications MaintenanceAppendix D. Fault Isolation Procedure Appendix B. Phone Jack Descriptions Appendix E. Command Index and Defaults Shelf-Mount Units Chapter Introduction Data Mode Features Software Fax ModeCommunications Software Class 1 Fax Communications Software Internet Browser Functional DescriptionPhysical Rear Panel 115 Vac Model RM16M Version RM16M Unit Electrical Installation Chapter InstallationAC Power Connection DC Power Connection DTE Connection Installation Digital Interface Signals Pin Signal Descriptions 140 Telephone Line Connection Dial Mode Pstn Connection Dial jack Direct connection to the Pstn is shown in Figure Leased Line Connection TELSET/LEASED Line Jack Leased Line Connection 115 Vac Model RM16M Connections Shelf-Mount RM16M V.3600 InstallationPage Chapter Getting Started Power-UpOption Selection Placing a Call Autodialing from a Terminal with the AT CommandsDialing with a Standard Telephone Autodialing from Front Panel Ending a Call Answering a Call Condition Reasons for Call Termination Reasons for Call Termination Page LED Descriptions Chapter Front Panel Operation LCD Menu Operation LCD Menus Main Menu Submenu Submenu Item Option Com Reg Main Menu LCD Messages Reg Remote Initiate RATION? OPTIONS? Submenu Main Menu Option Com Reg Lease line only † Dial line only 3600 Modify Change DTE Speed DTE=DCE Modify Change DTE Dial Method Async Modify Change DTE RTS/CTS Delay Password of 0000 disables front panel security 3600 Front Panel Security Page Command Categories Chapter AT CommandsOperation Modes Offline Command Mode Sending Commands to the ModemOnline Command Mode Autobaud Guidelines for Creating Command Statements Creating a Command Statement AT Repeating a Command a Command Statement BufferMonitor Display Backspace Key Numbered Commands Response CommandsGroup Commands Response Displays Q Digit / Word SelectionNegotiation Displays W Connect Message Codes \V Call Progress / Connect Speed Messages Number Code Application *RC Command Code Set Number Operation Message Meaning Response Number Codes / Messages DTE rate 31200 bps Connect 300/V42 Connect 300/MNP5 Dialing D Dial Commands Pulse Dialing P Tone Dialing TInsert Long Pause Remaining in Command Mode Switching to Answer Mode after Dialing RWait for Second Dial Tone W Hook Flash Dialing a Stored Telephone Number Sn Wait for 5 Seconds of Silence @Autodial Number Location *AUn Voice Calls AT Command Answer a Switching from Voice to DataManual Answer Autoanswer S0 Caller ID Messages Modem sends this message Distinctive Ring *DR Data Carrier Detect &C Terminal Interface Commands Data Terminal Ready &D Data Set Ready &S Request to Send / Clear to Send &R Serial Port Ring Indicator Pin 22 \R Changing from Data Mode to Command Mode +++ General CommandsDTE Controlled Fallback Rate Pin 23 *FB Local Character Echo E Hanging Up H, H1 Online Character Echo FFast Disconnect H2, H3 Eprom Check Speaker Volume LSpeaker Control M Return Online O Asynchronous / Synchronous Mode Selection &MLong Space Disconnect Y Bis Guard Tones &G Comman Operation Make / Break Dial Pulse Ratio &P Rate Selection Thresholds *TH Synchronous Transmit Clock Source &XAsymmetric Bit Rates *AS Modulation *MM Maximum DCE Speed %B Minimum DCE Speed %L Automatic Rate Adaption %R Auto Retrain %E Product Revision Level %V Manual Rate Adaption *RR Product Serial Number $V Online Quick Reference $HTalk / Data *DA Fast Train *FT Wire Operation Disable AT Command Set *NTPrivate Line Operation Dial Line Transmit Level *TDn Wire Dial-up Operation Wire Leased Line Operation Dial Backup Return to Leased Line from Dial Backup *LB Dial Backup *DBManual Dial Backup *LD Dial / Leased Line &L Configuration Profiles Configuration CommandsActive Profile Stored Profile Powerup Option Set &Y Storing a Configuration &W Load Factory Options &Fn Reset to Stored Configuration Z View Configuration Profiles/Received Signal Options &V Storing a Telephone Command Line &Zx=n, *CNx,n, *ND Soft Download Password %P1, $Y Remote ConfigurationRetaining / Restoring Options *RO Remote Security Code %P= Remote Configuration Security Enabling/Disabling Remote Configuration *RA Entering Remote Configuration %T=, &T Remote Configuration Format *RF Remote Configuration DTE Speed *RB Remote Configuration Saving or Discarding Options *RQ Page Reliable Mode Ccitt V.42 bis Error Control ProtocolChapter Protocols Normal Mode Auto-Reliable ModeConstant Speed Interface Data Compression Protocol Commands Direct ModeFlow Control Command Operation Disconnect buffer delay disabled Disconnect Buffer Delay Q%DSerial Port DTE Constant Speed \J Constant Operating Mode \N Optional Detection Phase \MCommand Operation Fast detect data sequence disabled Fast detect data sequence enabled Auto-Reliable Fallback Character %An Command OperationLAPM, MNP, or normal try both protocols Fallback to normal if not successful Serial Port Flow Control \Q Enable CTS/RTS bilateral flow control Enable data link flow control Command Operation Disable data link flow controlXON/XOFF Pass Through \X Data Link Flow Control \G Break option Break Control \Kn Maximum Reliable Block Size \A Inactivity Timer \T Set Auto-Reliable Buffer \C Transmit Break / Set Break Length \B42bis Data Compression %C Page Test Categories Chapter Test Mode OperationTest Offline Online Grant remote requested digital loopback Terminating a Test in Progress Q&T Local Analog Loopback &T1 Testing the Local Modem Local Analog Loopback with Self Test &T8 Testing the Remote Modem Grant/Deny RDL Request &T4, &T5 Local Digital Loopback &T3 Remote Digital Loopback with Self Test &T7 Remote Digital Loopback &T6 Command Operation Bilateral digital loop disabled Bilateral Digital Test Enable / Disable *DGBilateral digital loop enabled Test Pattern %T RDL enabled pin Command Operation Ignore pinLAL enabled pin DTE Controlled Remote Digital Loopback Pin Autocallback Security Chapter Security Operating without Low Security Low Security OperationOperating with Low Security Remote Operation Local Operation PasswordsLCD Indication of Security Restrictions in Security Operation High Security Low Security Commands Security Levels Superuser Default Passwords High Security CommandsEnabling High Security $EH=pw Disabling High Security $D Setting Passwords $Pn=pw$pwSet Security Levels $Ln=m Display Extended Feature Status $W? Extended Features $WDisplay/Reset Illegal Access Attempt Counters $M, $Mn, $M Set User Callback Number $Cn=m Removing a User $Rn Factory Reset $F=pw$pwSecurity Status $E? Local Logoff Command $$ Local Logon Command $n=pwDisplay User Status $S? Verify User Information $In, $IBn $n=pw Remote Logon Procedure $n=pw Fax Operation Chapter Fax Operation Modem Initialization Fax DefaultsFax Autoanswer Class 1 Details Fax Associated OptionsStored Fax Profile Dial Command D Class 1 Commands AT Responses to the ATD Command Answer Command a Service Class Capabilities +FCLASS=? Service Class Indication +FCLASS?On Hook H Off Hook H1 Receive Silence +FRS=Time Transmit Silence +FTS=TimeFax Transmit and Receive Modes Value Modulation Speed Facsimile Receive +FRM=Mod Facsimile Transmit +FTM=Mod Hdlc Receive +FRH=Mod Hdlc Transmit +FTH=ModTest Supported Range of Values +FTx=?, +FRx=? Command Description Class 1 Result Code +FCERRORBinary File Transfer Fax Autoanswer +FAA= Registers Chapter Status Registers Changing S-Register Values Changing Register Values Sn=v, Sn=v Register Operation Sn?, Sn? ATSn.#=v Individual Bit Command Sn . # =v Ring Count S1 Autoanswer S0Escape Character S2 End-of-Line Character S3 Carrier Detect Time S9 Pause Interval for Comma S8Lost Carrier Detect Time S10 Dtmf Tone Duration S11 S13 Escape Sequence Pause S12 S15 Bit Mapped S14 System Tests S16 Test Timeout S18S17 S19 Bit Mapped S22 Bit Mapped S21 Bit Mapped S23 RTS/CTS Delay S26S24 DTR State Recognition S25 Bit Mapped S27 Lookback Timer S28Bit Mapped S29 S31 Bit Mapped S30 Remote Configuration Escape Character S41 DTR / Dial Backup Number to Dial S35Bit Mapped S32 S33 S43 Remote Configuration Guard Time S42XON Character from DTE S44 Xoff Character from DTE S45 Automatic Rate Adaption Threshold S53 Leased Line Transmit Level S52Flow Control S54 Compression Control S56 S55Bit Mapped S57 Break Control S59 Inactivity Timer S58Bit Mapped S60 DTE Options S61 Disconnect Buffer Delay S62Maximum Transmit Block Size S63 S65-66 Auto-Reliable Fallback Character S64Link Speed Status S67 S68 33,600 bps DCE Independent Speed S69 Operating Mode Status S71 Operating Mode S70Enable V.42 fast detect Lapm or MNP or native auto-reliable Callback Delay S74 Password Timeout S73Bit Mapped S72 Callback Retry S75 Autocallback Timer S78 Callback Retry Delay S76Lockout Threshold S77 Break Length S79 S80 register indicates the serial port speed Serial Port or DTE Speed S80 Minimum DCE Speed S81 Enable negotiation statusNegotiation Status S82 S83 Modulation Type S88 S85-S87S89-S90 Current Modulation S91 Asymmetric Settings S96 Settings S95S92 S94 Bit Mapped S97 Select Sync Data Chapter Bis Autodialer Software Guidelines Autodialer Command Strings and Parameters Invalid Responses Access these formats using Dial Parameters Dial Parameters Dial Command CRN nn...n Bis Commands and Responses Intermediate Call Progress Response Program Number Command PRN ann...nDial Stored Number CRS a Disregard Incoming Call DIC Request List of Stored Numbers RLN Redial Last Number CRR n Connect Incoming Call CICLink Number by Address PRL ab Request List of Delayed Numbers RLD RLD Request List of Linked Numbers RLL Request List of Version RLV Modem Options Command PRO xxxyy00 Invms Invalid command message syntax error Examples PRO011 Restore Factory Settings PRP n Save Current Settings PRK Request List of Stored Options RLO xxx yy Options Option Definition Settings Default 11-16 3600 3600 11-17 Settings Default Fuse Replacement Chapter MaintenanceMaintenance General Calling Technical Support Maintenance Appendix a Specifications Fax Rates Modem Data RatesModulations Fax Modulation RTS/CTS Delay TestingCarrier Detect Level Telco ConnectionPage Dial Pin Functions Appendix B Phone Jack DescriptionsTELSET/LEASED Line Pin Functions Page Jumper Option Selection Appendix C Hardware OptionsRemoving the Cover Figure C-1. Cover Removal Figure C-2. Jumper Location for Ground Option Ground Option Jumper Replacing the Cover Fault Isolation Procedure Appendix D Fault Isolation ProcedureTelephone Interface Standard Phone Part Modem and Telephone Line Check 3600 Page Command Reg Description Appendix E Command Index and Defaults Speaker off when carrier is present Set H command to V.32 †Response displays on Response messages Wait for dial tone, detect busy signal Negotiation display enabledRestore factory configuration 1 † Appropriate connect codes Asynchronous dial / asynchronous data Dial line †39/61 pulse make / break ratio CTS forced on View configuration profiles Grant remote commanded digitalStore current configuration to user option Powerup with user option set #1 Bps max Disable disconnect buffer delay Transmit a break signal Disable automatic rate adaptionDisable auto-reliable buffer Disable slaved DTE/DCE speed When call is answered Enables bilateral CTS/RTS flowLapm with MNP and normal fallback Switches modem to talk mode † Disable protocol result codesManual dial backup operation Disables bilateral digital loop AT command set enabled Command Reg Description Automode modulationOriginate 15 4800 bps, 18 9600 bps 10-2BER High rate selection threshold Distinctive Ring Commands Caller ID CommandsFax Commands Class 1 Commands Valid in Only Fax Mode Can be one of the following values 0 or Disable security Security CommandsHigh Security Reinitialize security Disable user changes password and callback number Enable remote configuration Remote Configuration Commands Status Registers Default Reg Function Factory Set Reg Function Factory Set 10-27 Current modulation Synchronous Description Command Bis Dialer Commands Response Messages Response Message Meaning Factory Option Set #1 Factory Option Sets Factory Option Set # Factory Option Set #3 Modem Options DCE rate Factory Option Set #5 Factory Option Set # Synchronous 2-wire Leased Line Normal Originate AT&F7 Synchronous 2-wire Leased Line Forced Answer AT&F8 Factory Option Set #9 Page Binary Decimal Hexadecimal Appendix F Ascii and Ebcdic Characters Decimal Hex Symbol Key Symbol ¢ cent ACK0 143 144 145 Ascii and Ebcdic Characters Ascii and Ebcdic Characters EIA Appendix G Abbreviations and Acronyms Abbreviations and Acronyms PIW Xmit What You Need Appendix H Flash UpgradeSteps For Downloading Flash Upgrade Troubleshooting Appendix I Country-Specific Parameters India Default Available Command Command Name Option Options Japan Malaysia Universal/International Flash Upgrade Service and Support Page Two Year Limited Hardware Warranty Motorola Limited Hardware WarrantyWhat This Warranty Does Not Cover General Provisions Warranty-2 Numerals Index Index-2 Index-3 Index-4 Index-5 Index-6 Index-7 Index-8 Index-9 Index-10 3600 Index-11 Index-12 Index-13