Manuals / Motorola / Computer Equipment / Modem

Motorola V.3600 manual Bit Mapped S21, Bit Mapped S22

Models: V.3600

1 271

Download 271 pages 30.48 Kb

Page 150

Status Registers

Bit Mapped — S21

Bit	Value	Command	Description

6,	00	&S	DSR forced on
0	10	&S1	DSR on when online
	01	&S2	DSR off 5 seconds after disconnect
	11	&S3	DSR follows off hook (OH)

5,	00	&C	DCD always on
1	10	&C1	DCD on while carrier present
	01	&C2	DCD on except for 5 seconds after disconnect
			DCD follows RTS on remote modem; not valid
	11	&C3	in reliable mode

2	0	&R	CTS follows RTS by S26 delay
	1	&R1	CTS always on

4,	00	&D	Modem ignores DTR
3	01	&D1	Modem assumes command mode when DTR
			turns off
	10	&D2	Modem hangs up when DTR turns off
	11	&D3	Modem resets when DTR turns off

7	0	Y	Long space disconnect disabled
	1	Y1	Long space disconnect enabled

Bit Mapped — S22

Bit	Value	Command	Description

1,	00	L	Speaker volume low
0	01	L1	Speaker volume low
	10	L2	Speaker volume low
	11	L3	Speaker volume high

3,	00	M	Speaker off
2	01	M1	Speaker on until carrier detect
	10	M2	Speaker always on
	11	M3	Speaker off when modem is dialing

6-4	000	X	CONNECT message only, blind dials, no busy
			detect
	001	X1	CONNECT / appropriate code for rate, blind
			dials, no busy detect
	010	X2	CONNECT / appropriate code for rate, waits
			for dial tone, no busy detect
	011	X3	CONNECT / appropriate code for rate, blind
			dials, reports BUSY
	100	X4	CONNECT / appropriate code for rate,
			waits for dial tone, reports BUSY

10-10

V.3600

Image 150

Motorola V.3600 manual Bit Mapped S21, Bit Mapped S22

Contents

3600 Modem User’s GuideMotorola Updates CopyrightTrademarks Regulatory Information FCC RequirementsFCC Part 15 Declaration Of Conformity FCC Fax Branding RequirementsModel Name V.3600, 115 VAC version only Shielded Cables Model Name V.3600, all other versionsSpecial Requirements For Canada Industry Canada IC RequirementsRinger Equivalence Number Canadian Emission Requirements V.3600, other versionsPage Contents Contents Contents Test Mode Operation ProtocolsSecurity Fax Operation Status RegistersContents 25 bis Autodialer Appendix D. Fault Isolation Procedure MaintenanceAppendix A. Specifications Appendix B. Phone Jack DescriptionsAppendix E. Command Index and Defaults Chapter Introduction Shelf-Mount UnitsFeatures Data ModeCommunications Software Class 1 Fax Communications Software Fax ModeSoftware Internet BrowserDescription FunctionalPhysical Rear Panel 115 Vac Model RM16M Unit RM16M VersionAC Power Connection Chapter InstallationElectrical Installation DC Power ConnectionInstallation DTE ConnectionDigital Interface Signals Pin Signal Descriptions 140 Dial Mode Pstn Connection Dial jack Telephone Line ConnectionLeased Line Connection TELSET/LEASED Line Jack Direct connection to the Pstn is shown in FigureLeased Line Connection 115 Vac Model Shelf-Mount RM16M V.3600 Installation RM16M ConnectionsPage Power-Up Chapter Getting StartedOption Selection Dialing with a Standard Telephone Autodialing from a Terminal with the AT CommandsPlacing a Call Autodialing from Front PanelAnswering a Call Ending a CallReasons for Call Termination ConditionReasons for Call Termination Page Chapter Front Panel Operation LED DescriptionsLCD Menus LCD Menu OperationMain Menu LCD Messages Reg Main Menu Submenu Submenu Item Option Com RegRemote Initiate Submenu Main Menu Option Com Reg RATION? OPTIONS?Lease line only † Dial line only 3600 Modify Change DTE Speed DTE=DCE Modify Change DTE Dial Method Async Modify Change DTE RTS/CTS Delay Password of 0000 disables front panel security 3600 Front Panel Security Page Chapter AT Commands Command CategoriesOperation Modes Sending Commands to the Modem Offline Command ModeOnline Command Mode Creating a Command Statement AT Autobaud Guidelines for Creating Command StatementsMonitor Display Command Statement BufferRepeating a Command a Backspace KeyResponse Commands Numbered CommandsGroup Commands Negotiation Displays W Digit / Word SelectionResponse Displays Q Connect Message Codes \VCall Progress / Connect Speed Messages Command Code Set Number Operation Number Code Application *RCResponse Number Codes / Messages Message MeaningDTE rate 31200 bps Connect 300/V42 Connect 300/MNP5 Dial Commands Dialing DTone Dialing T Pulse Dialing PInsert Long Pause Wait for Second Dial Tone W Switching to Answer Mode after Dialing RRemaining in Command Mode Hook FlashAutodial Number Location *AUn Wait for 5 Seconds of Silence @Dialing a Stored Telephone Number Sn Voice CallsManual Answer Switching from Voice to DataAT Command Answer a Autoanswer S0Distinctive Ring *DR Caller ID Messages Modem sends this messageTerminal Interface Commands Data Carrier Detect &CData Set Ready &S Data Terminal Ready &DSerial Port Ring Indicator Pin 22 \R Request to Send / Clear to Send &RDTE Controlled Fallback Rate Pin 23 *FB General CommandsChanging from Data Mode to Command Mode +++ Local Character Echo EOnline Character Echo F Hanging Up H, H1Fast Disconnect H2, H3 Speaker Volume L Eprom CheckSpeaker Control M Long Space Disconnect Y Asynchronous / Synchronous Mode Selection &MReturn Online O Bis Guard Tones &GMake / Break Dial Pulse Ratio &P Comman OperationAsymmetric Bit Rates *AS Synchronous Transmit Clock Source &XRate Selection Thresholds *TH Modulation *MMMaximum DCE Speed %B Minimum DCE Speed %L Auto Retrain %E Automatic Rate Adaption %RManual Rate Adaption *RR Product Revision Level %VTalk / Data *DA Online Quick Reference $HProduct Serial Number $V Fast Train *FTPrivate Line Operation Disable AT Command Set *NTWire Operation Dial Line Transmit Level *TDnWire Leased Line Operation Wire Dial-up OperationDial Backup Manual Dial Backup *LD Dial Backup *DBReturn to Leased Line from Dial Backup *LB Dial / Leased Line &LActive Profile Configuration CommandsConfiguration Profiles Stored ProfileStoring a Configuration &W Powerup Option Set &YReset to Stored Configuration Z Load Factory Options &FnStoring a Telephone Command Line &Zx=n, *CNx,n, *ND View Configuration Profiles/Received Signal Options &VRemote Configuration Soft Download Password %P1, $YRetaining / Restoring Options *RO Remote Configuration Security Remote Security Code %P=Entering Remote Configuration %T=, &T Enabling/Disabling Remote Configuration *RARemote Configuration DTE Speed *RB Remote Configuration Format *RFRemote Configuration Saving or Discarding Options *RQ Page Ccitt V.42 bis Error Control Protocol Reliable ModeChapter Protocols Constant Speed Interface Auto-Reliable ModeNormal Mode Data CompressionDirect Mode Protocol CommandsFlow Control Serial Port DTE Constant Speed \J Disconnect Buffer Delay Q%DCommand Operation Disconnect buffer delay disabled ConstantCommand Operation Fast detect data sequence disabled Optional Detection Phase \MOperating Mode \N Fast detect data sequence enabledLAPM, MNP, or normal try both protocols Command OperationAuto-Reliable Fallback Character %An Fallback to normal if not successfulEnable CTS/RTS bilateral flow control Serial Port Flow Control \QXON/XOFF Pass Through \X Command Operation Disable data link flow controlEnable data link flow control Data Link Flow Control \GBreak Control \Kn Break optionInactivity Timer \T Maximum Reliable Block Size \ATransmit Break / Set Break Length \B Set Auto-Reliable Buffer \C42bis Data Compression %C Page Chapter Test Mode Operation Test CategoriesTest Offline Online Terminating a Test in Progress Q&T Grant remote requested digital loopbackTesting the Local Modem Local Analog Loopback &T1Testing the Remote Modem Local Analog Loopback with Self Test &T8Local Digital Loopback &T3 Grant/Deny RDL Request &T4, &T5Remote Digital Loopback &T6 Remote Digital Loopback with Self Test &T7Bilateral digital loop enabled Bilateral Digital Test Enable / Disable *DGCommand Operation Bilateral digital loop disabled Test Pattern %TLAL enabled pin Command Operation Ignore pinRDL enabled pin DTE Controlled Remote Digital Loopback PinChapter Security Autocallback SecurityOperating with Low Security Low Security OperationOperating without Low Security Remote OperationLCD Indication of Security PasswordsLocal Operation Restrictions in Security OperationLow Security Commands High SecuritySecurity Levels Superuser High Security Commands Default PasswordsEnabling High Security $EH=pw Setting Passwords $Pn=pw$pw Disabling High Security $DSet Security Levels $Ln=m Display/Reset Illegal Access Attempt Counters $M, $Mn, $M Extended Features $WDisplay Extended Feature Status $W? Set User Callback Number $Cn=mFactory Reset $F=pw$pw Removing a User $RnSecurity Status $E? Display User Status $S? Local Logon Command $n=pwLocal Logoff Command $$ Verify User Information $In, $IBnRemote Logon Procedure $n=pw $n=pwChapter Fax Operation Fax OperationFax Defaults Modem InitializationFax Autoanswer Fax Associated Options Class 1 DetailsStored Fax Profile Class 1 Commands Dial Command DAnswer Command a AT Responses to the ATD CommandOn Hook H Service Class Indication +FCLASS?Service Class Capabilities +FCLASS=? Off Hook H1Fax Transmit and Receive Modes Transmit Silence +FTS=TimeReceive Silence +FRS=Time Value Modulation SpeedFacsimile Transmit +FTM=Mod Facsimile Receive +FRM=ModHdlc Transmit +FTH=Mod Hdlc Receive +FRH=ModTest Supported Range of Values +FTx=?, +FRx=? Binary File Transfer Class 1 Result Code +FCERRORCommand Description Fax Autoanswer +FAA=Chapter Status Registers RegistersChanging S-Register Values Register Operation Sn?, Sn? Changing Register Values Sn=v, Sn=vIndividual Bit Command Sn . # =v ATSn.#=vEscape Character S2 Autoanswer S0Ring Count S1 End-of-Line Character S3Lost Carrier Detect Time S10 Pause Interval for Comma S8Carrier Detect Time S9 Dtmf Tone Duration S11Escape Sequence Pause S12 S13Bit Mapped S14 S15S17 Test Timeout S18System Tests S16 S19Bit Mapped S21 Bit Mapped S22S24 RTS/CTS Delay S26Bit Mapped S23 DTR State Recognition S25Lookback Timer S28 Bit Mapped S27Bit Mapped S29 Bit Mapped S30 S31Bit Mapped S32 DTR / Dial Backup Number to Dial S35Remote Configuration Escape Character S41 S33XON Character from DTE S44 Remote Configuration Guard Time S42S43 Xoff Character from DTE S45Leased Line Transmit Level S52 Automatic Rate Adaption Threshold S53Flow Control S54 S55 Compression Control S56Bit Mapped S57 Inactivity Timer S58 Break Control S59Bit Mapped S60 Disconnect Buffer Delay S62 DTE Options S61Maximum Transmit Block Size S63 Link Speed Status S67 Auto-Reliable Fallback Character S64S65-66 S68DCE Independent Speed S69 33,600 bpsEnable V.42 fast detect Operating Mode S70Operating Mode Status S71 Lapm or MNP or native auto-reliableBit Mapped S72 Password Timeout S73Callback Delay S74 Callback Retry S75Lockout Threshold S77 Callback Retry Delay S76Autocallback Timer S78 Break Length S79Serial Port or DTE Speed S80 S80 register indicates the serial port speedNegotiation Status S82 Enable negotiation statusMinimum DCE Speed S81 S83S89-S90 S85-S87Modulation Type S88 Current Modulation S91S92 S94 Settings S95Asymmetric Settings S96 Bit Mapped S97Chapter Bis Autodialer Select Sync DataAutodialer Command Strings and Parameters Software GuidelinesAccess these formats using Invalid ResponsesDial Parameters Dial ParametersBis Commands and Responses Dial Command CRN nn...nProgram Number Command PRN ann...n Intermediate Call Progress ResponseDial Stored Number CRS a Request List of Stored Numbers RLN Disregard Incoming Call DICConnect Incoming Call CIC Redial Last Number CRR nLink Number by Address PRL ab Request List of Delayed Numbers RLD Request List of Linked Numbers RLL RLDModem Options Command PRO xxxyy00 Request List of Version RLVInvms Invalid command message syntax error Examples PRO011 Save Current Settings PRK Restore Factory Settings PRP nRequest List of Stored Options RLO xxx yy Option Definition Settings Default Options11-16 3600 3600 11-17 Settings Default Maintenance Chapter MaintenanceFuse Replacement GeneralMaintenance Calling Technical SupportAppendix a Specifications Modulations Modem Data RatesFax Rates Fax ModulationCarrier Detect Level TestingRTS/CTS Delay Telco ConnectionPage Appendix B Phone Jack Descriptions Dial Pin FunctionsTELSET/LEASED Line Pin Functions Page Appendix C Hardware Options Jumper Option SelectionRemoving the Cover Figure C-1. Cover Removal Figure C-2. Jumper Location for Ground Option Replacing the Cover Ground Option JumperTelephone Interface Appendix D Fault Isolation ProcedureFault Isolation Procedure Standard PhoneModem and Telephone Line Check Part3600 Page Appendix E Command Index and Defaults Command Reg DescriptionResponse displays on Set H command to V.32 †Speaker off when carrier is present Response messagesRestore factory configuration 1 † Negotiation display enabledWait for dial tone, detect busy signal Appropriate connect codes39/61 pulse make / break ratio Dial line †Asynchronous dial / asynchronous data CTS forced onStore current configuration to user option Grant remote commanded digitalView configuration profiles Powerup with user option set #1Disable disconnect buffer delay Bps maxDisable auto-reliable buffer Disable automatic rate adaptionTransmit a break signal Disable slaved DTE/DCE speedEnables bilateral CTS/RTS flow When call is answeredLapm with MNP and normal fallback Manual dial backup operation Disable protocol result codesSwitches modem to talk mode † Disables bilateral digital loopOriginate Command Reg Description Automode modulationAT command set enabled 15 4800 bps, 18 9600 bpsHigh rate selection threshold 10-2BERFax Commands Caller ID CommandsDistinctive Ring Commands Class 1 Commands Valid in Only Fax ModeCan be one of the following values 0 or High Security Security CommandsDisable security Reinitialize securityDisable user changes password and callback number Remote Configuration Commands Enable remote configurationDefault Reg Function Factory Set Status RegistersReg Function Factory Set 10-27 Current modulation Bis Dialer Commands Synchronous Description CommandResponse Messages Response Message Meaning Factory Option Sets Factory Option Set #1Factory Option Set # Factory Option Set #3 Modem Options DCE rate Factory Option Set #5 Factory Option Set # Synchronous 2-wire Leased Line Normal Originate AT&F7 Synchronous 2-wire Leased Line Forced Answer AT&F8 Factory Option Set #9 Page Appendix F Ascii and Ebcdic Characters Binary Decimal HexadecimalSymbol Key Decimal HexSymbol ¢ cent ACK0 143 144 145 Ascii and Ebcdic Characters Ascii and Ebcdic Characters Appendix G Abbreviations and Acronyms EIAAbbreviations and Acronyms PIW Xmit Appendix H Flash Upgrade What You NeedSteps For Downloading Troubleshooting Flash UpgradeAppendix I Country-Specific Parameters Default Available Command Command Name Option Options IndiaJapan Malaysia Universal/International Flash Upgrade Service and Support Page What This Warranty Does Not Cover Motorola Limited Hardware WarrantyTwo Year Limited Hardware Warranty General ProvisionsWarranty-2 Index NumeralsIndex-2 Index-3 Index-4 Index-5 Index-6 Index-7 Index-8 Index-9 Index-10 3600 Index-11 Index-12 Index-13