Replacing the Toner Cartridge, Cleaning the Drum | Muratec F-112

Replacing the Toner Cartridge

When the toner eventually runs out, only blank pages print when a print job is sent or when a fax is received. At this stage, the toner cartridge needs to be replaced. The display on the control panel shows the warning message, “Toner Empty” and the machine stops printing.

NOTE: You can set the machine to ignore the “Toner Empty” message and continue printing. See page 5.8.

1Open the front cover.

2Lightly pushing the used cartridge down, pull it out.

3Unpack the new toner cartridge and gently roll it horizontally four or five times to distribute the toner evenly inside the cartridge.

Save the box and the cover for shipping.

4Slide the new toner cartridge in until it locks into place.

5Close the front cover.

Setting the Notify Toner Option

If you have set the Notify Toner menu option to “On”, your machine automatically sends a fax to your service company or the dealer to notify them that your machine requires a new toner cartridge when the toner cartridge needs to be replaced. The fax number is preset by your dealer when you bought your machine.

1Press Menu on the control panel until “Maintenance” appears on the top line of the display.

The first available menu item, “Clean Drum,” displays on the bottom line.

2	Press the scroll button (	or	) to display “Notify Toner ” on the	5
	bottom line and press Enter.			5
3	Press the scroll button (	or	) to change the setting.

Select “On” to enable this feature. Selecting “Off” disables this feature.

4Press Enter to save the selection.

Cleaning the Drum

If there are streaks or spots on your print, the OPC drum of the cartridge may require cleaning.

1Before setting the cleaning procedure, make sure that paper is loaded in the machine.

2Press Menu on the control panel until “Maintenance” appears on the top line of the display.

The first available menu item, “Clean Drum,” displays on the bottom line.

3Press Enter.

MAINTENANCE 5.7

Image 71

Muratec F-112 user manual Replacing the Toner Cartridge, Setting the Notify Toner Option, Cleaning the Drum

Contents

Page Page Contents Receiving a Fax Setting the Paper Type and Size for the Manual Feeder Input Misfeed Exit Misfeed Changing Setting Options Advanced Fax Setting OptionsPaper Feeding Problems Copying Problems Important Precautions and Safety Information Laser Safety Statement Radio Frequency Emissions Ozone SafetyPower Saver Recycling Viii Canadian Radio Interference RegulationsFax Branding Ringer Equivalence Number You should also know that Limited warranty Page Getting Started TAM Lead for UK only Unpacking Clearance Space Selecting a Location These are the main components of your machine Understanding the Component LocationFront View Rear View Starts a job Control Panel Functions O P Y Document Output Support Attaching Accessories Handset and Handset Cradle Installing the Toner Cartridge You can load approximately 250 sheets Loading Paper Changing the Paper Size in the Paper Tray Wall jack Connecting the Telephone Line To view your display text in another language, see the next Turning the Machine On Changing the Display Language Setting the Machine ID Entering Characters Using the Number Keypad Inserting a Pause Setting the Date and TimeKeypad Letters and Numbers Changing Numbers or Names Changing the Clock Mode Setting the Paper Type and Size You can control the following sounds Setting SoundsSpeaker, Ringer, Key Sound and Alarm Sound Speaker Volume Toll Save Mode Using the Save ModesToner Save Mode Power Save Mode Setting Up the Fax System Option Description Available Fax Setup Options Basic Functions Loading a Document Preparing a Document Mode Recommended for Adjusting the Document Resolution Sending a Fax Manually Sending a Fax Automatically To redial the number you last called Redialing the Last NumberConfirming Transmission Automatic Redialing Loading Paper for Receiving Faxes About Receiving Modes Receiving Automatically in Ans/Fax Mode Receiving Automatically in Fax ModeReceiving Manually in Tel Mode Receiving Faxes Using the Drpd Mode Receiving Manually Using an Extension Telephone Receiving Faxes in the Memory Loading Paper for Copying Adjust the guide to the width of the print material Use the scroll button Line. Press Enter to access the menu itemOpen the rear cover to use the rear output slot After copying, close the rear cover Making a Copy Setting Copy Options On the display Press Reduce/Enlarge or the scroll button or untilCustom50-150% displays on the bottom line. Press Enter Setting the Time Out Option Changing the Default Settings Press Start Copy/Fax to begin copying Collation CopyingPage Storing a Number for Speed Dialing Speed Dialing Line and press Enter Setting a Group Dial NumberGroup Dialing Editing Group Dial Numbers Searching with a Particular First Letter Searching for a Number in the MemoryPrinting a Phonebook List Searching Sequentially through the Memory Advanced FAX Functions Sending Broadcasting Faxes Sending a Delayed Fax Advanced FAX Polling a Remote Machine Sending a Priority Fax Advanced FAX Or until you see the fax job you want to To cancel your selection, press 2 to select No Additional Features Bottom line and press Enter Press the scroll button Using Secure Receiving Mode Printing Reports Printing a Report Using Advanced Fax SettingsChanging Setting Options Advanced Fax Setting Options RCV Forward Memo Maintenance Clearing the Memory Cleaning the Inside Adjusting ShadingCleaning Your Machine Cleaning the Outside Cleaning the Scan Unit Disassemble the white roller as follows Expected Cartridge Life Maintaining the Toner CartridgeToner Cartridge Storage Saving Toner Replacing the Toner Cartridge Setting the Notify Toner OptionCleaning the Drum Items Yield Average Consumables and Replacement PartsIgnoring the Toner Empty Message Replacing the ADF Rubber Pad Memo Troubleshooting Exit Misfeed Clearing Document JamsInput Misfeed Message Location of Jam Go to Clearing Paper JamsPaper Tray Fuser Area or Around the Toner Cartridge Paper Exit Area Tips for Avoiding Paper Jams Manual Feeder Display Meaning Suggested solutions Clearing LCD Error Messages Paper tray has run out Load paper in the paper tray. See One-touch or speed dial Dial the number manually usingLocation you tried to use has No number assigned to it For storing a number, see Condition Suggested solutions Solving ProblemsPaper Feeding Problems Copying Problems Faxing Problems Specifications Characters x 2 lines General Specifications Copier Specifications Facsimile Specifications Supported Sizes of Paper Paper SpecificationsSize mm/in Weight Capacity Overview Category Specifications Guidelines for Using PaperPaper Specifications Paper Storage Environment Memo Index Page Visit us at