ENGLISH

USER MANUAL

HYDRAULIC SYSTEM OIL COOLER FIN CLEANING CHECK

WARNING!

Protect body parts (eyes, hair, hands, etc.) properly, when performing cleaning procedures using compressed air or water gun.

1.Empty the hopper (7, Fig. G); if it contains a small quantity of waste, it is not necessary to dump it.

2.Drive the machine on a solid and level ground, then engage the parking brake (13, Fig. E).

3.Lift the hopper (7, Fig. G), according to the procedure shown in the relevant paragraph.

4.Turn the ignition key (24, Fig. D) to OFF position and remove it.

5.To avoid that the hopper lowers by accident, install the lifted hopper support rods (3, Fig. F), according to the instructions shown on the relevant paragraph.

6.Close the left and right side upper lids (9 and 28, Fig. G) by engaging the fasteners (10) and (29) with the supplied key.

7.Remove the screws, then remove the engine compartment panel (11, Fig. F).

8.Open the right side lower lid (34, Fig. G) by disengaging the fastener (35) with the supplied key.

9.Clean the hydraulic system oil cooler fins (9, Fig. F) with compressed air (maximum 87.0 psi [6 Bar]). If necessary, point the compressed air in the opposite direction of the cooling air.

10.Inside the radiator (9, Fig. F), check that the fan turns freely.

11.Perform steps 3 to 8 in the reverse order.

BATTERY FLUID LEVEL CHECK

WARNING!

Protect body parts (eyes, hair, hands, etc.) properly, when performing battery check and cleaning procedures.

1.Engage the parking brake (13, Fig. E).

2.Turn the ignition key (24, Fig. D) to OFF position and remove it.

3.Open the left side lower lid (11, Fig. G) by disengaging the fastener (12) with the supplied key.

4.Check the electrolyte level in the battery (34, Fig. F) and, if necessary, top up with distilled water.

5.If necessary, clean the battery.

6.Check the battery terminal connections for oxidation.

7.Close the left side lower lid (11, Fig. G) by engaging the fastener (12) with the supplied key.

BRAKE FLUID LEVEL CHECK

1.Engage the parking brake (13, Fig. E).

2.Turn the ignition key (24, Fig. D) to OFF position and remove it.

3.Check the brake system fluid level in the tank (1, Fig. AB). The level must be at 0.4 in (1 cm) from the tank filler neck. If necessary, top up using the same type of fluid that is in the line.

Type of fluid used: DOT4.

REVERSE GEAR BUZZER SENSOR CHECK

1.Check that, when the machine moves in reverse, the relevant buzzer sounds.

If necessary, perform the adjustment according to the instructions in the Service Manual.

TYRE PRESSURE CHECK

1.Engage the parking brake (13, Fig. E).

2.Turn the ignition key (24, Fig. D) to OFF position and remove it.

3.The tyre pressure should be as follows:

•

Front tyres:

72.5 psi (5.0 Bar)

•

Rear tyres:

72.5 psi (5.0 Bar)

WARNING!

Please respect the recommended tyre pressure as stated in the relevant decals.

The manufacturer rating is based on standard drive speed and standard load rating, different from the actual machine application.

34

33014576(4)2008-02 A

RS 850

Page 147 Page 149
Page 148
Image 148
Nilfisk-ALTO RS 850 Hydraulic System OIL Cooler FIN Cleaning Check, Battery Fluid Level Check, Brake Fluid Level Check
Page 147 Page 149

RS 850 specifications

Nilfisk-ALTO RS 850: An Overview of Features, Technologies, and Characteristics

The Nilfisk-ALTO RS 850 is a sophisticated industrial vacuum cleaner designed to meet the rigorous demands of various sectors, including manufacturing, construction, and food processing. Recognized for its reliability, it offers a combination of powerful performance, advanced technology, and robust construction, making it an ideal choice for professionals seeking efficiency and effectiveness in their cleaning tasks.

One of the standout features of the RS 850 is its powerful motor which delivers impressive suction capabilities. With a high air flow rate, the vacuum can easily extract dust, dirt, and other debris from both hard and soft surfaces, ensuring a thorough clean. Its large capacity dust container allows for extended cleaning sessions without the need for frequent emptying, which increases productivity and reduces downtime.

The RS 850 also incorporates advanced filtration technology, including a HEPA filter that effectively traps fine particles and allergens. This feature is especially beneficial in environments where air quality is paramount, as it helps to maintain a cleaner, healthier workspace. The filter is washable, ensuring long-term use and reducing maintenance costs.

Designed with ergonomics in mind, the Nilfisk-ALTO RS 850 is equipped with user-friendly controls that simplify operation. Its lightweight design and maneuverability make it easy to transport to various job sites, while the durable construction ensures it can withstand tough working conditions. The machine features robust wheels and an adjustable handle, allowing for seamless navigation across different terrains.

Moreover, the RS 850 showcases a range of attachments and accessories that enhance its versatility. Users can easily switch between different nozzles and brushes, allowing for tailored cleaning solutions for various surfaces, whether it be hard floors, carpets, or upholstery.

A significant advantage of the Nilfisk-ALTO RS 850 is its low noise operation, making it suitable for use in noise-sensitive environments. This feature permits cleaning activities during business hours without disrupting workflows.

In conclusion, the Nilfisk-ALTO RS 850 stands out as a top-tier industrial vacuum cleaner. Its powerful suction, effective filtration, user-centric design, and versatility make it an essential tool for professionals dedicated to maintaining a clean and efficient work environment. Whether in manufacturing, construction, or other demanding applications, the RS 850 delivers exceptional performance and reliability, reinforcing Nilfisk’s commitment to quality and innovation in cleaning technology.
Top Page Image Contents