USER MANUAL

ENGLISH

SUCTION INLET DISASSEMBLY/ASSEMBLY

NOTE

This is a basic procedure, it is often recalled during other procedures, when necessary.

Disassembly

1.Remove the side brooms (see the procedure in the relevant paragraph).

2.Move the 3rd broom (21, Fig. G) aside, and lower the suction inlet (17) according to the procedure shown in the relevant paragraph.

3.Engage the parking brake (13, Fig. E).

4.Turn the ignition key (24, Fig. D) to OFF position and remove it.

5.Mark the position of the pipes (1 and 2, Fig. AY) (for proper assembly), then disconnect them from the suction inlet (3) and plug them.

6.Mark the position of the pipes (4 and 5, Fig. AY) (for proper assembly), then disconnect them from the suction inlet (3) and plug them.

7.Disconnect the dust control system pipes (6 and 7, Fig. AY).

8.Disconnect the electrical connectors (8 and 9, Fig. AY) and remove the gasket.

9.Remove the screws (10, Fig. AY).

10.Move the suction inlet (3, Fig. AY) forward, and loosen the suction pipe clamp (11).

11.Disconnect the suction pipe (12, Fig. AY) from the suction inlet.

12.On both sides of the suction inlet, unscrew the nuts (13, Fig. AY) and disconnect the relevant springs.

13.Remove the suction inlet (3).

14.Collect the pipes (15, Fig. AY) disconnected from the suction inlet, and secure them with clamps (14). Fit a dust boot to prevent dirt and foreign material from entering the pipes (15).

Assembly

15.Assemble the components in the reverse order of disassembly.

16.If necessary, check the suction inlet and skirt height and operation (see the procedure in the relevant paragraph).

3RD BROOM ARM DISASSEMBLY/ASSEMBLY

NOTE

This is a basic procedure, it is often recalled during other procedures, when necessary.

CAUTION!

This procedure is applicable only for sweepers with appropriate fittings for installation of snow brush.

Disassembly

1.Extend the 3rd broom arm (23, Fig. G) and lift the broom (21) according to the procedure shown in the relevant paragraph.

2.Turn off the engine and engage the parking brake (13, Fig. E).

3.Operating according to the safety rules, with a proper hoisting system (1, Fig. AZ), sling the 3rd broom arm (2) in the points shown in the figure. Move the pipes and cable aside, to avoid squashing them during the lifting operation.

3rd broom arm weight: approximately 176.4 (80 kg).

4.Disconnect the electrical connector (3, Fig. AZ).

5.Disconnect the hydraulic system quick couplings (4, Fig. AZ) from the corresponding pipe couplings (5), then install the protection covers.

6.Disconnect the dust control system quick coupling (6, Fig. AZ) from the corresponding pipe coupling (7), then install the protection covers.

7.Inside the cab, remove the screw (8, Fig. AZ), then remove the panel (9).

8.Slightly tighten the hoisting system (1, Fig. AZ), then remove the screws (10) and the nut (11).

9.Remove the 3rd broom arm (2, Fig. AZ).

Assembly

10.Assemble the components in the reverse order of disassembly.

11.If necessary, check and adjust the 3rd broom position (see the procedure in the relevant paragraph).

RS 850

33014576(4)2008-02 A

41

Page 155
Image 155
Nilfisk-ALTO RS 850 Suction Inlet DISASSEMBLY/ASSEMBLY, 3RD Broom ARM DISASSEMBLY/ASSEMBLY, Disassembly, Assembly

RS 850 specifications

Nilfisk-ALTO RS 850: An Overview of Features, Technologies, and Characteristics

The Nilfisk-ALTO RS 850 is a sophisticated industrial vacuum cleaner designed to meet the rigorous demands of various sectors, including manufacturing, construction, and food processing. Recognized for its reliability, it offers a combination of powerful performance, advanced technology, and robust construction, making it an ideal choice for professionals seeking efficiency and effectiveness in their cleaning tasks.

One of the standout features of the RS 850 is its powerful motor which delivers impressive suction capabilities. With a high air flow rate, the vacuum can easily extract dust, dirt, and other debris from both hard and soft surfaces, ensuring a thorough clean. Its large capacity dust container allows for extended cleaning sessions without the need for frequent emptying, which increases productivity and reduces downtime.

The RS 850 also incorporates advanced filtration technology, including a HEPA filter that effectively traps fine particles and allergens. This feature is especially beneficial in environments where air quality is paramount, as it helps to maintain a cleaner, healthier workspace. The filter is washable, ensuring long-term use and reducing maintenance costs.

Designed with ergonomics in mind, the Nilfisk-ALTO RS 850 is equipped with user-friendly controls that simplify operation. Its lightweight design and maneuverability make it easy to transport to various job sites, while the durable construction ensures it can withstand tough working conditions. The machine features robust wheels and an adjustable handle, allowing for seamless navigation across different terrains.

Moreover, the RS 850 showcases a range of attachments and accessories that enhance its versatility. Users can easily switch between different nozzles and brushes, allowing for tailored cleaning solutions for various surfaces, whether it be hard floors, carpets, or upholstery.

A significant advantage of the Nilfisk-ALTO RS 850 is its low noise operation, making it suitable for use in noise-sensitive environments. This feature permits cleaning activities during business hours without disrupting workflows.

In conclusion, the Nilfisk-ALTO RS 850 stands out as a top-tier industrial vacuum cleaner. Its powerful suction, effective filtration, user-centric design, and versatility make it an essential tool for professionals dedicated to maintaining a clean and efficient work environment. Whether in manufacturing, construction, or other demanding applications, the RS 850 delivers exceptional performance and reliability, reinforcing Nilfiskā€™s commitment to quality and innovation in cleaning technology.