Snow brush assembly, Snow brush disassembly

USER MANUAL

ENGLISH

SNOW BRUSH ASSEMBLY AND USE (optional)

CAUTION!

To install this equipment, the sweeper should be equipped with the appropriate ﬁtting.

Snow brush assembly

1.Disassemble the suction inlet (17, Fig. G) (see the procedure in the relevant paragraph).

2.Disassemble the 3rd broom arm (23, Fig. G) (see the procedure in the relevant paragraph).

3.Operating on a level ground, bring the sweeper into a suitable position to install the snow brush (Fig. AV).

4.Turn off the engine and engage the parking brake (13, Fig. E).

5.Place the snow brush on the arms (19, Fig. AV) and secure it with the screws (14).

6.On both sides of the machine, tighten the brush height adjusting screws (15 and 16, Fig. AV) on the arms (19). If necessary, this adjustment can be performed afterwards, to adjust the lifted snow brush.

7.Lift the adjustable feet (5, Fig. AV) completely and secure it with the knobs (6).

8.Remove the protection cover, then connect the hydraulic system quick couplings (1, Fig. AV) to the corresponding pipe couplings (2).

9.Open the left side lower lid (11, Fig. G) by disengaging the fastener (12) with the supplied key.

10.Turn the lever (21, Fig. AV) from the position (21a) (high-pressure water gun activation) to the position (21b) (snow brush activation).

11.Close the left side lower lid (11, Fig. G) by engaging the fastener (12) with the supplied key.

12.Now the machine is ready to operate with the snow brush.

Snow brush disassembly

13.Disassemble the snow brush in the reverse order of assembly.

14.Secure and protect the snow brush properly.

Snow brush use

15.Assemble the snow brush (Fig. AV) according to the procedure shown in the relevant paragraphs.

16.To lift/lower the snow brush use the suction inlet lifting/lowering controls.

17.To have the snow brush rotating, turn the lever (8, Fig. E) to “OPT” position.

18.To change the snow brush speed according to engine speed, use the knob (22, Fig. AV).

19.Before using the snow brush (10, Fig. AV), check its height from the ground according to the following procedure.

•Drive the machine with the snow brush on a level ground.

•Keep the machine stationary, lower the snow brush completely and let it rotate for few seconds.

•Stop and lift the snow brush, then move the machine aside and engage the parking brake.

•Check that the brush print (20, Fig. AV), along its length, is 0.8 to 1.6 in (2 to 4 cm) wide.

•If the print is not within the speciﬁcations, remove the pins (13, Fig. AV) and adjust by lifting/lowering the wheels (11) with the winches (12).

•When the adjustment is completed, place the winches (12) in the original position and install the pins (13).

20.Engage the parking brake with the lever (13, Fig. E).

21.Lift the snow brush, then turn off the engine by turning the ignition key (24, Fig. D) counterclockwise, to the end of stroke, then remove it.

22.Remove the clip (9, Fig. AV) and disconnect the rod (17) from the pin (8).

23.Tilt the brush assembly as necessary, then connect the hole (18, Fig. AV) to the relevant pin (8). Reinstall the clip (9).

24.Now the machine is ready to operate with the snow brush.

If necessary, ﬁt snow chains on the front wheels of the sweeper.

RS 850

33014576(4)2008-02 A

RS 850 specifications

Nilfisk-ALTO RS 850: An Overview of Features, Technologies, and Characteristics

The Nilfisk-ALTO RS 850 is a sophisticated industrial vacuum cleaner designed to meet the rigorous demands of various sectors, including manufacturing, construction, and food processing. Recognized for its reliability, it offers a combination of powerful performance, advanced technology, and robust construction, making it an ideal choice for professionals seeking efficiency and effectiveness in their cleaning tasks.

One of the standout features of the RS 850 is its powerful motor which delivers impressive suction capabilities. With a high air flow rate, the vacuum can easily extract dust, dirt, and other debris from both hard and soft surfaces, ensuring a thorough clean. Its large capacity dust container allows for extended cleaning sessions without the need for frequent emptying, which increases productivity and reduces downtime.

The RS 850 also incorporates advanced filtration technology, including a HEPA filter that effectively traps fine particles and allergens. This feature is especially beneficial in environments where air quality is paramount, as it helps to maintain a cleaner, healthier workspace. The filter is washable, ensuring long-term use and reducing maintenance costs.

Designed with ergonomics in mind, the Nilfisk-ALTO RS 850 is equipped with user-friendly controls that simplify operation. Its lightweight design and maneuverability make it easy to transport to various job sites, while the durable construction ensures it can withstand tough working conditions. The machine features robust wheels and an adjustable handle, allowing for seamless navigation across different terrains.

Moreover, the RS 850 showcases a range of attachments and accessories that enhance its versatility. Users can easily switch between different nozzles and brushes, allowing for tailored cleaning solutions for various surfaces, whether it be hard floors, carpets, or upholstery.

A significant advantage of the Nilfisk-ALTO RS 850 is its low noise operation, making it suitable for use in noise-sensitive environments. This feature permits cleaning activities during business hours without disrupting workflows.

In conclusion, the Nilfisk-ALTO RS 850 stands out as a top-tier industrial vacuum cleaner. Its powerful suction, effective filtration, user-centric design, and versatility make it an essential tool for professionals dedicated to maintaining a clean and efficient work environment. Whether in manufacturing, construction, or other demanding applications, the RS 850 delivers exceptional performance and reliability, reinforcing Nilfisk’s commitment to quality and innovation in cleaning technology.

Nilfisk-ALTO RS 850 Snow brush assembly, Snow brush disassembly, Snow brush use

Models: RS 850