Broom Replacement, Parking Brake Check

USER MANUAL

ENGLISH

3rd broom height adjustment

4.Operate on the tensioning self-locking nut (5, Fig. AI) of the spring (6) and consider the following:

•To lower the broom, the nut (5) must be unscrewed;

•To lift the broom, the nut (5) must be screwed.

5.Perform step 1 again.

3rd broom forward tilting angle (4, Fig. AH) adjustment

6.Loosen the locknuts (7 and 8, Fig. AI), then adjust the forward tilting angle (4) by placing a lever in the hole (10) and turning the tie rod (9).

7.When the adjustment is completed, tighten the locknuts (7) and (8).

8.Perform step 1 again.

9.When the broom is too worn out the adjustment is no more possible; replace the broom according to the instructions in the relevant paragraph.

BROOM REPLACEMENT

NOTE

Brooms of various hardness are available. This procedure is applicable to all types of brooms.

CAUTION!

It is advisable to use protective gloves when replacing the side brooms because there can be sharp debris between the bristles.

1.Lift the brooms and engage the parking brake (13, Fig. E).

2.Turn the ignition key (24, Fig. D) to OFF position and remove it.

3.Remove the lower centre screw (1, Fig. AJ), then remove the broom (2) to be replaced. Recover the key.

4.Remove the screws (3, Fig. AJ) and the ﬂange (4) from the removed broom.

5.Install the ﬂange (4, Fig. AJ) and secure it with the screws (3) on the new broom.

6.Install the new broom (2, Fig. AJ) with the key, then tighten the centre screw (1).

7.Adjust the height of the new broom according to the procedure shown in the relevant paragraph.

PARKING BRAKE CHECK

1.Engage the parking brake lever (13, Fig. E) and check for proper operation. Check also that the brake operates in the same way on both the front wheels.

2.If necessary, adjust the parking brake according to the instructions in the Service Manual.

ENGINE OIL LEVEL CHECK

1.Engage the parking brake (13, Fig. E).

2.Turn the ignition key (24, Fig. D) to OFF position and remove it.

3.Open the left side lower lid (11, Fig. G) by disengaging the fastener (12) with the supplied key.

4.Check the oil level as shown in the diesel engine Manual.

5.Close the left side lower lid (11, Fig. G) by engaging the fastener (12) with the supplied key.

ENGINE OIL CHANGE

1.Empty the hopper (7, Fig. G); if it contains a small quantity of waste, it is not necessary to dump it.

2.Drive the machine on a solid and level ground, then engage the parking brake (13, Fig. E).

3.Lift the hopper (7, Fig. G), according to the procedure shown in the relevant paragraph.

4.Turn the ignition key (24, Fig. D) to OFF position and remove it.

5.To avoid that the hopper lowers by accident, install the lifted hopper support rods (3, Fig. F), according to the instructions shown on the relevant paragraph.

6.Close the left and right side upper lids (9 and 28, Fig. G) by engaging the fasteners (10) and (29) with the supplied key.

7.Remove the screws, then remove the engine compartment panel (11, Fig. F).

8.Open the left side lower lid (11, Fig. G) by disengaging the fastener (12) with the supplied key.

9.Change the oil as shown in the diesel engine Manual.

10.Perform steps 3 to 8 in the reverse order.

RS 850

33014576(4)2008-02 A

RS 850 specifications

Nilfisk-ALTO RS 850: An Overview of Features, Technologies, and Characteristics

The Nilfisk-ALTO RS 850 is a sophisticated industrial vacuum cleaner designed to meet the rigorous demands of various sectors, including manufacturing, construction, and food processing. Recognized for its reliability, it offers a combination of powerful performance, advanced technology, and robust construction, making it an ideal choice for professionals seeking efficiency and effectiveness in their cleaning tasks.

One of the standout features of the RS 850 is its powerful motor which delivers impressive suction capabilities. With a high air flow rate, the vacuum can easily extract dust, dirt, and other debris from both hard and soft surfaces, ensuring a thorough clean. Its large capacity dust container allows for extended cleaning sessions without the need for frequent emptying, which increases productivity and reduces downtime.

The RS 850 also incorporates advanced filtration technology, including a HEPA filter that effectively traps fine particles and allergens. This feature is especially beneficial in environments where air quality is paramount, as it helps to maintain a cleaner, healthier workspace. The filter is washable, ensuring long-term use and reducing maintenance costs.

Designed with ergonomics in mind, the Nilfisk-ALTO RS 850 is equipped with user-friendly controls that simplify operation. Its lightweight design and maneuverability make it easy to transport to various job sites, while the durable construction ensures it can withstand tough working conditions. The machine features robust wheels and an adjustable handle, allowing for seamless navigation across different terrains.

Moreover, the RS 850 showcases a range of attachments and accessories that enhance its versatility. Users can easily switch between different nozzles and brushes, allowing for tailored cleaning solutions for various surfaces, whether it be hard floors, carpets, or upholstery.

A significant advantage of the Nilfisk-ALTO RS 850 is its low noise operation, making it suitable for use in noise-sensitive environments. This feature permits cleaning activities during business hours without disrupting workflows.

In conclusion, the Nilfisk-ALTO RS 850 stands out as a top-tier industrial vacuum cleaner. Its powerful suction, effective filtration, user-centric design, and versatility make it an essential tool for professionals dedicated to maintaining a clean and efficient work environment. Whether in manufacturing, construction, or other demanding applications, the RS 850 delivers exceptional performance and reliability, reinforcing Nilfisk’s commitment to quality and innovation in cleaning technology.

Nilfisk-ALTO RS 850 Broom Replacement, Parking Brake Check, Engine OIL Level Check

Models: RS 850