Procedure from installation to operation | Omron BU3002SW, BU1002SW

Procedure from installation to operation

Read“Safety precautions” Page 4

Remove the product from the package and check the contents Page 12

Perform installation and

connection Page 21

Are you	Yes
using UPS monitoring
software or contact
signal?

Start

Installation/connection

Read“Using the UPS monitoring software and contact signal” Page 65

No

Check the operation and displays Pages 31

Charge the battery

Page 33

Measure the backup time

Page 33

Charge the battery again Page 33

*Preparation for operation is complete.

Operate Page 34

Perform maintenance

and inspection Page 53

Replace the battery

Page 54

Replace the fan

Page 62

Preparation for operation

No

Maintenance/

Deteriorated

battery?Fan stopped? inspection

No

Yes	Yes

2

Image 4

Omron BU3002SW, BU1002SW specifications Procedure from installation to operation, Start Installation/connection

Contents

BU1002SW/BU3002SW Introduction Internal Battery Procedure from installation to operation Start Installation/connection Table of Contents Keep plastic package bags out of reach of children Safety precautionsMisuse may cause death or serious injury Do not disassemble, repair, or modify the unit Provide secure groundingDo not pinch or tie the cable of the unit Doing so may compromise the safety of devices Do not allow the unit to come in contact with water If fluid leaks from the unit, do not touch the fluid Do not insert metal objects into the battery connectors Perform replacement on a stable and flat placeUse a specified battery for replacement Do not disassemble or modify the battery Do not put the battery into fire and do not break it Do not use a new battery and an old battery at the same time Do not perform a withstand voltage test Quitting Battery Mode RebootingScheduled operation using the UPS monitoring software This unit uses lead acid batteries Preparation 2Checking the contentsUnpacking the product Name of each part Front view Side view Rear view BU1002SW BU3002SW Explanation of symbols used on unit Installation and connection Precautions and notes on installation and connection Do not install the unit in other than specified orientations Installation and connection Do not perform a withstand voltage test Installation and connection BU1002SW BU3002SW Casters locked Connecting the equipment Group control of power supply output Connecting a device to the power supply output BU1002SW Output on Output OFF Nfpa Input plug L6-15P Front view Connecting a device to the power supply output BU3002SW BU3002SW Rated value of output capacity Max kVA/2100W Rear panel Input plug L6-20P Front view Checking the operation Turn on the units power switchBring all the connected devices into operation Battery Mode, check the units LED display and beep sound OFF Measuring the initial value of backup time Charging the batteryRecharging the battery Precautions and notes for operation Operation Explanation Start procedure Start and stop procedures and basic operationOperation Turn on the power switch of the UPS Operation after a power failure Setting switch 1 can be used to turn the beeper ON/OFF. Stop procedure Operation during recovery from a power failureConnection capacity/battery level meter Interpreting beeps and displays Displays and beeps in normal operation Display and beep for battery replacement Suspending a beep UPS functionsSelf-diagnosis test Description of the auto battery test function Changing the setting of the functions Setting switch function list UPS functions BS signal reception time corresponds to the setting switch BS signal valid range setting setting switch Settings available for this operation are shown below UPS operation mode settingsSettable items and explanations OFF Settings Cold start Measuring the backup time How to measure backup timeEstimated backup time For Windows Server 2003/XP/Me/2000/Windows NT/Linux/Mac BUM100S Maintenance and Inspection Checking the batteryLife of battery estimated replacement timing Methods for checking the battery Replacing the battery Battery recycling Procedure for recycling the battery Do not hold the connector or cable of the battery pack Tighten the 2 screws Battery replacement is now complete Red tape Tighten 2 screws After replacing the battery during operation Replacing the fan Do not put your fingers into the fan Fan replacement procedure Cleaning Cleaning the UPS Using the UPS monitoring software and contact signal UPS monitoring software Software title Connect the UPS to a computer RS-232C When using UPS Power Manager UPS monitoring software for Mac When connecting 2 or more computers to the UPS Explanation Install the included UPS service driver on the computer Connector Perform UPS service setup Click Recycling and Discarding the Battery Stopping the UPS How to set up UPS service set the time to shut down Windows Check Set Click Check Set Check Set Contact signal Contact SignalSignal output Low battery level signal output BL Items that can be set using the contact signal card Remote ON/OFF Signal Output delay time setting for backup signal output BU BU/BL signal reverse output setting Insert/ removal method of contact signal card Contact Signal Connector female DSUB9P Remote ON/OFF connector Contact Signal ratingsContact Signal circuit inside the UPS Example of the use of the Contact Signal circuit Precautions and notes for the use of the Contact Signal Remote ON/OFF circuit Using an SNMP/Web card Adding an SNMP/Web card Specifications Description featuresSNMP/Web card outline Extending the backup time Connecting an additional battery unit Adding BUM300S to the BU3002SW Troubleshooting Problem Check and remedy Specifications References Dimensions BU3002SW Circuit block diagram Related products K1L-D-06051B