Using an SNMP/Web card, Adding an SNMP/Web card | Omron BU1002SW

8．Using an SNMP/Web card

8. Using an SNMP/Web card

8-1 Adding an SNMP/Web card

An SNMP/Web card can be loaded into the card slot on the back of the unit. Remove the contact signal card that the unit came equipped with, and plug the SNMP/Web card in its place. Store the removed contact signal card in a safe place.

•SNMP/Web card (model number: SC20G), sold separately

(1)Remove the 2 screws, and carefully pull out the contact signal card.

BU1002SW

BU3002SW

(2)Carefully insert the SNMP/Web card (model number: SC20G), and securely tighten the 2 screws. * Replace with BU50SW/BU75SW/BU100SW/BU150SW/BU1002SW/BU3002SW brackets.

BU1002SW

BU3002SW

83

Image 85

Omron BU1002SW, BU3002SW specifications Using an SNMP/Web card, Adding an SNMP/Web card

Contents

BU1002SW/BU3002SW Introduction Internal Battery Start Installation/connection Procedure from installation to operation Table of Contents Keep plastic package bags out of reach of children Safety precautionsMisuse may cause death or serious injury Do not disassemble, repair, or modify the unit Provide secure groundingDo not pinch or tie the cable of the unit Doing so may compromise the safety of devices If fluid leaks from the unit, do not touch the fluid Do not allow the unit to come in contact with water Perform replacement on a stable and flat place Do not insert metal objects into the battery connectorsUse a specified battery for replacement Do not disassemble or modify the battery Do not use a new battery and an old battery at the same time Do not put the battery into fire and do not break it Do not perform a withstand voltage test Rebooting Quitting Battery ModeScheduled operation using the UPS monitoring software This unit uses lead acid batteries Preparation 2Checking the contentsUnpacking the product Front view Name of each part Side view BU1002SW BU3002SW Rear view Explanation of symbols used on unit Precautions and notes on installation and connection Installation and connection Do not install the unit in other than specified orientations Installation and connection Do not perform a withstand voltage test BU1002SW Installation and connection BU3002SW Casters locked Group control of power supply output Connecting the equipment Output on Output OFF Connecting a device to the power supply output BU1002SW Nfpa Input plug L6-15P Front view BU3002SW Rated value of output capacity Max kVA/2100W Connecting a device to the power supply output BU3002SW Rear panel Input plug L6-20P Front view Checking the operation Turn on the units power switchBring all the connected devices into operation OFF Battery Mode, check the units LED display and beep sound Measuring the initial value of backup time Charging the batteryRecharging the battery Operation Precautions and notes for operation Explanation Start procedure Start and stop procedures and basic operationOperation Turn on the power switch of the UPS Setting switch 1 can be used to turn the beeper ON/OFF. Operation after a power failure Stop procedure Operation during recovery from a power failureConnection capacity/battery level meter Displays and beeps in normal operation Interpreting beeps and displays Display and beep for battery replacement Suspending a beep UPS functionsSelf-diagnosis test Changing the setting of the functions Description of the auto battery test function Setting switch function list UPS functions BS signal reception time corresponds to the setting switch BS signal valid range setting setting switch Settings available for this operation are shown below UPS operation mode settingsSettable items and explanations OFF Settings Cold start How to measure backup time Measuring the backup timeEstimated backup time For Windows Server 2003/XP/Me/2000/Windows NT/Linux/Mac BUM100S Checking the battery Maintenance and InspectionLife of battery estimated replacement timing Methods for checking the battery Replacing the battery Procedure for recycling the battery Battery recycling Do not hold the connector or cable of the battery pack Tighten the 2 screws Battery replacement is now complete Red tape Tighten 2 screws After replacing the battery during operation Do not put your fingers into the fan Replacing the fan Fan replacement procedure Cleaning the UPS Cleaning UPS monitoring software Using the UPS monitoring software and contact signal Software title RS-232C Connect the UPS to a computer When connecting 2 or more computers to the UPS When using UPS Power Manager UPS monitoring software for Mac Explanation Install the included UPS service driver on the computer Connector Click Perform UPS service setup Stopping the UPS Recycling and Discarding the Battery Check Set Click How to set up UPS service set the time to shut down Windows Check Set Check Set Contact Signal Contact signalSignal output Low battery level signal output BL Remote ON/OFF Signal Items that can be set using the contact signal card BU/BL signal reverse output setting Output delay time setting for backup signal output BU Contact Signal Connector female DSUB9P Insert/ removal method of contact signal card Contact Signal ratings Remote ON/OFF connectorContact Signal circuit inside the UPS Example of the use of the Contact Signal circuit Remote ON/OFF circuit Precautions and notes for the use of the Contact Signal Adding an SNMP/Web card Using an SNMP/Web card Specifications Description featuresSNMP/Web card outline Connecting an additional battery unit Extending the backup time Adding BUM300S to the BU3002SW Problem Check and remedy Troubleshooting References Specifications BU3002SW Dimensions Related products Circuit block diagram K1L-D-06051B